Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for i-ART)

DTC    P2009    Intake Manifold Runner Control Circuit Low (Bank 1)

DTC    P2010    Intake Manifold Runner Control Circuit High (Bank 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2006 .

P2009 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
2 seconds after engine is started, race engine for 1 second
Open in No. 1 vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
  1. No. 1 vacuum switching valve (for swirl control valve)
  2. Open in No. 1 vacuum switching valve (for swirl control valve) circuit
  3. ECM

P2010 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
2 seconds after engine is started, race engine for 1 second
Short in No. 1 vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
  1. No. 1 vacuum switching valve (for swirl control valve)
  2. Short in No. 1 vacuum switching valve (for swirl control valve) circuit
  3. ECM

WIRING DIAGRAM

Refer to DTC P2006 .

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
A067588E16
  1. Connect the GTS to the DLC3.

  1. Disconnect the vacuum hoses from the No. 1 vacuum switching valve (for swirl control valve).

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

  1. Check the VSV operation when it is operated using the GTS.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

  1. Reconnect the vacuum hoses.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT NO. 1 VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
  1. Inspect the No. 1 vacuum switching valve (for swirl control valve) .



NG
Go to step 8
OK


3.INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)


    A258904E07
  1. Disconnect the No. 1 vacuum switching valve (for swirl control valve) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vacuum Switching Valve (for No. 1 Swirl Control Valve))

  1. Reconnect the No. 1 vacuum switching valve (for swirl control valve) connector.



NG
Go to step 6
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)
  1. Disconnect the No. 1 vacuum switching valve (for swirl control valve) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    S35-1 - E28-7 (SCV)
    Always
    Below 1 Ω
    S35-1 or E28-7 (SCV) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the No. 1 vacuum switching valve (for swirl control valve) connector.

  1. Reconnect the ECM connector.



NG
Go to step 9
OK


5.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10

6.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 1 integration relay connector.

  1. Disconnect the No. 1 vacuum switching valve (for swirl control valve) connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1J-5 - S35-2
    Always
    Below 1 Ω
    1J-5 or S35-2 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the No. 1 integration relay.

  1. Reconnect the No. 1 integration relay connector.

  1. Reconnect the No. 1 vacuum switching valve (for swirl control valve) connector.



NG
Go to step 9
OK


7.INSPECT ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NEXT
Go to step 10

8.REPLACE VACUUM CONTROL VALVE SET
  1. Replace the vacuum control valve set .



NEXT
Go to step 10

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace harness or connector.


NEXT


10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine and wait for 3 seconds or more.

  1. 2 seconds after the engine is started, race the engine for 1 second.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END