FUEL INJECTOR (w/o Glow Plug Controller) > INSTALLATION |
| 1. INSTALL INJECTOR ASSEMBLY |
![]() |
Install 4 new injection nozzle seats to the cylinder head.
Apply a small amount of clean engine oil to 4 new O-rings.
![]() |
Install an O-ring to each injector as shown in the illustration.
Insert the 4 injectors into the cylinder head.
For an injector that has been replaced with a new injector, register the injector compensation code.
![]() |
Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.
![]() |
Temporarily install the 4 injection pipes with the union nuts.
![]() |
Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.
If scratches or dents are present, replace the nozzle leakage pipe.
![]() |
Set the leakage pipe and 5 new gaskets in place.
Apply a small amount of oil to the 4 injector hollow screws and union bolt.
Temporarily install the nozzle leakage pipe with the 4 injector hollow screws and union bolt.
Tighten the 4 holder clamp bolts.
Remove the 4 injection pipes.
![]() |
Tighten the 4 injector hollow screws in order from 1 to 4.
Tighten the union bolt.
| 2. INSPECT FOR FUEL LEAK |
![]() |
Check that there are no leaks from the nozzle leakage pipe connection.
Install the gasket and No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).
Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.
![]() |
Install SST (turbocharger pressure gauge) to the fuel return side of the leakage pipe, and maintain 100 kPa (1.0 kgf/cm2, 14.5 psi) of pressure for 60 seconds to check that no bubbles form.
After checking for fuel leaks, wipe off the soapy water from the leakage pipe connection.
Remove SST, No. 2 nozzle leakage pipe and gasket.
| 3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.
Remove any old seal packing (FIPG material) from the cylinder head.
![]() |
Apply seal packing to the specific areas shown in the illustration.
Install a new cylinder head cover gasket and the cylinder head cover with the 10 bolts and 2 nuts.
Install 4 new nozzle holder seals.
Connect the ventilation hose.
Connect the 4 connectors and install the 3 bolts.
| 4. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.
Temporarily install a new gasket and the union bolt.
Tighten the 3 bolts and union bolt.
Connect the 3 fuel hoses.
| 5. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
w/ EGR Cooler:
Install the bolt.
w/o EGR Cooler:
Install the 2 bolts.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 6. TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler) |
Set a new gasket to the cylinder head.
![]() |
Temporarily install the electric EGR control valve with No. 2 EGR valve and EGR cooler with the 2 nuts and bolt.
Connect the vacuum hose to the No. 2 EGR valve.
Connect the EGR valve position sensor connector.
| 7. INSTALL NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler) |
Set a new gasket labeled A to the No. 2 intake air connector as shown in the illustration.
Insert the No. 2 intake air connector with the gasket into the electric EGR control valve.
Install a new gasket labeled B to the electric EGR control valve side shown in the illustration.
| 8. TEMPORARILY INSTALL INTAKE AIR CONNECTOR (w/ EGR Cooler) |
Set a new gasket labeled C to the intake manifold.
Temporarily install the intake air connector to the intake manifold with the 3 bolts.
Temporarily install the intake air connector and electric EGR control valve with the 3 nuts shown in the illustration.

| 9. TIGHTEN NO. 2 INTAKE AIR CONNECTOR AND INTAKE AIR CONNECTOR (w/ EGR Cooler) |
Tighten the 3 nuts labeled A shown in the illustration.
| 10. TIGHTEN INTAKE AIR CONNECTOR AND INTAKE MANIFOLD (w/ EGR Cooler) |
Tighten the 3 bolts labeled B shown in the illustration.
| 11. TIGHTEN EGR COOLER (w/ EGR Cooler) |
Tighten the bolt labeled C shown in the illustration.
Tighten the 2 nuts labeled D shown in the illustration.

| 12. INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler) |
![]() |
Temporarily install the No. 2 intake air connector bracket with the 3 bolts.
Tighten the bolt labeled A.
Tighten the 2 bolts labeled B.
| 13. INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler) |
w/ EGR Cooler:
Install the electric vacuum regulating valve together with the bracket with the 2 bolts.
Connect the 4 vacuum hoses.
Connect the connector.
w/o EGR Cooler:
Install the vacuum switching valve with the screw.
Install the electric vacuum regulating valve together with the bracket with the 2 bolts.
Connect the 3 vacuum hoses.
Connect the 2 connectors.
| 14. INSTALL NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler) |
Install the No. 1 gas filter with gas filter bracket with the bolt.
Connect the 2 vacuum hoses.
| 15. CONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler) |
Connect the No. 3 water by-pass pipe with wire harness with the 2 bolts.
| 16. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
w/ EGR Cooler:
Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts as shown in the illustration.
![]() |
w/o EGR Cooler:
Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts as shown in the illustration.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 17. CONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler) |
![]() |
Connect the No. 4 water by-pass hose to the EGR cooler.
| 18. CONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler) |
Connect the No. 3 water by-pass hose to the EGR cooler.
Install the clamp.
| 19. INSTALL DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler) |
| 20. INSTALL INTERCOOLER ASSEMBLY (w/o EGR Cooler) |
| 21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 22. ADD ENGINE COOLANT (w/ EGR Cooler) |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 23. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs.
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 24. PERFORM REGISTRATION |
Perform registration of injector compensation code.
Perform registration of pilot quantity learning.
| 25. INSPECT FOR COOLANT LEAK (w/ EGR Cooler) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 26. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 27. INSPECT FOR OIL LEAK |
| 28. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.