Home › BODY › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining)

FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining, w/o Front Seat Side Airbag)


    B211340
  1. Temporarily install the power seat motor assembly (for Reclining) with the 3 bolts.



    B211341
  1. Install the reclining rod.



    B211336
  1. Attach the 6 claws to install the push nut to the reclining rod.

  1. Using a 4 mm socket hexagon wrench, tighten the 3 bolts.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }



    B277644
  1. Attach the 8 hooks to install the seatback spring.

  1. Connect the connector.



2. INSTALL NO. 2 SEAT WIRE (w/ Front Seat Side Airbag)


B277656
  1. Attach the 2 wire harness clamps to install the No. 2 seat wire.

  1. w/ Front Seat Side Airbag:
    Connect the front power seat motor assembly (for Reclining) connector.



3. INSTALL RECLINING ADJUSTER INSIDE COVER RH (w/ Front Seat Side Airbag)
  1. Attach the claw to install the reclining adjuster inside cover RH.

  1. Install the screw.



4. INSTALL RECLINING ADJUSTER INSIDE COVER LH (w/o Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover LH.

  1. Install the screw.



5. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the claw to install the reclining adjuster inside cover LH.

  1. Install the screw.



6. INSTALL NO. 1 SEATBACK CLOTH


    B277283
  1. Install the No. 1 seatback cloth to the separate type front seatback spring assembly.



7. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    B207459
  1. Install the separate type front seatback pad to the separate type front seatback spring assembly.



8. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


  1. Using hog ring pliers, attach the strap of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B290641E01


    Text in Illustration 
    *1
    Hog Ring Pliers
    -
    -
    *a
    Front view of front seatback
    *b
    Rear view of front seatback

  1. Attach the 4 claws to install the 2 front seat headrest support assemblies.



    B284733
  1. w/ Front Seat Side Airbag:
    Attach the separate type front seatback cover bracket and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the separate type front seatback cover is installed, make sure the separate type front seatback cover bracket is not twisted.



    B290643
  1. Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.



    B290644E01
  1. Using hog ring pliers, attach the strap of the separate type front seatback cover together with the No. 1 seatback cloth to the separate type front seatback spring assembly with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers



    B290645E01
  1. Pass the No. 2 seat wire through the hole of the separate type front seatback cover

  1. Using hog ring pliers, attach the wires at the bottom of the separate type front seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers



    B290633
  1. w/o Front Seat Side Airbag:
    Connect the No. 2 seat wire connector and attach the wire harness clamp.



9. INSTALL RECLINING ADJUSTER INSIDE COVER LH (w/ Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover LH.



10. INSTALL RECLINING ADJUSTER INSIDE COVER RH (w/ Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover RH.



11. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/ Front Seat Side Airbag)
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the 2 screws.



    B290633
  1. Connect the No. 2 seat wire connector and attach the wire harness clamp.



    B290632
  1. Attach the 4 front seat airbag wire harness clamps.



12. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


  1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat inner cushion shield LH.


    B278528



    B278526
  1. Attach the claw to temporarily install the front seat inner cushion shield LH.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.



    B278527
  1. Attach the guide and claw.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. Install the screw.



13. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT INNER NO. 1 SEAT CUSHION SHIELD LH
  1. Attach the claw and guide to install the front seat cushion shield LH with the front inner No. 1 seat cushion shield LH.

  1. Install the 3 screws.

  1. Install the 2 screws.



14. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B211475
  1. Attach the 4 claws to install the slide and vertical power seat switch knob.



15. INSTALL RECLINING POWER SEAT SWITCH KNOB


    B211476
  1. Attach the 2 claws to install the reclining power seat switch knob.



16. INSTALL FRONT SEAT ASSEMBLY
(Click here)


17. INSPECT FRONT SEAT ASSEMBLY
(Click here)