VEHICLE STABILITY CONTROL SYSTEM > ABS Warning Light Remains ON |

| 1.CHECK FOR DTC |
Check if DTCs for the ABS are output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S25-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-1 (GND1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C26 combination meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-10 (WA) - C26-38 | Always | Below 1 Ω |
| S25-10 (WA) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL) |
![]() |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S25-28 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| ABS Warning Light | ABS warning light | Warning light ON / OFF | Observe the combination meter. |
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| ABS Warning Light | ABS warning light / ON or OFF | ON: ABS warning light on OFF: ABS warning light off | - |
| Result | Proceed to | |
| Data List Display | Data List Display When Performing Active Test ON/OFF Operation | |
| ON | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
| OFF | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
|
| ||||
| A | ||
| ||