Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

If the skid control ECU (brake actuator assembly) stores a DTC, the VSC OFF indicator light blinks in the combination meter.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If VSC turns off, the VSC OFF indicator light will come on.
When the transfer position is LL, VSC is prohibited and the VSC OFF indicator and slip indicator lights turn on.

WIRING DIAGRAM


C237077E03


INSPECTION PROCEDURE

NOTICE:
  1. As there may be malfunctions in the transfer system related to when the transfer operates in LL, check the transfer system first (Click here).
  2. After replacing the brake actuator assembly, perform calibration (Click here).
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

1.CHECK FOR DTC
  1. Check if DTCs for the VSC are output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    VSC OFF switch / Normal, Unknown, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    -

  1. Check that the mode display changes according to VSC OFF switch operation.

    OK:
    The intelligent tester display changes according to VSC OFF switch operation.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    VSC Warning Light
    VSC OFF indicator light
    Indicator light ON / OFF
    Observe the combination meter.

  1. When performing the VSC Warning Light Active Test, check VSC Warning Light in the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    VSC Warning Light
    VSC OFF indicator light / ON or OFF
    ON: VSC OFF indicator light on
    OFF: VSC OFF indicator light off
    -


Result 
Result
Proceed to
Data List Display
Data List Display When Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
Go to step 7
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

4.INSPECT VSC OFF SWITCH
  1. Turn the ignition switch off.

  1. Remove the VSC OFF switch (Click here).

  1. Inspect the VSC OFF switch (Click here).



NG
REPLACE VSC OFF SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S25-30 (CSW) - V8-3
    Always
    Below 1 Ω
    S25-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    V8-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)


    C199357E76
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S25-28 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the C27 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S25-15 (VSCW) - C27-16
    Always
    Below 1 Ω
    S25-15 (VSCW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)