Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TRC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

Pressing the VSC OFF switch turns off traction control, and pressing and holding the switch turns off traction control and VSC. When VSC turns off, the VSC OFF and TRC OFF indicator lights turn on.

WIRING DIAGRAM

Refer to VSC OFF Indicator Light Remains ON .

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

1.CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)


    C199357E76
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S25-28 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.READ VALUE USING GTS (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    VSC OFF switch / Normal, Unknown, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    -

  1. Check that the mode display changes according to VSC OFF switch operation.

    OK:
    The GTS display changes according to VSC OFF switch operation.



NG
Go to step 4
OK


3.INSPECT BRAKE ACTUATOR ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Check the state of the TRC OFF indicator light.

    Result 
    Result
    Proceed to
    TRC OFF indicator light turns off
    A
    TRC OFF indicator light does not turn off
    B



B
Go to step 6
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

4.INSPECT VSC OFF SWITCH
  1. Turn the ignition switch off.

  1. Remove the VSC OFF switch (Click here).

  1. Inspect the VSC OFF switch (Click here).



NG
REPLACE VSC OFF SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S25-30 (CSW) - V8-3
    Always
    Below 1 Ω
    S25-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    V8-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the C27 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S25-23 (INFR) - C27-21
    Always
    Below 1 Ω
    S25-23 (INFR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)