Home › ENGINE ยท 1KD-FTV › FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL TANK TO FILLER PIPE HOSE


    A191370
  1. Install the fuel tank to filler pipe hose to the fuel tank.



2. INSTALL FUEL TANK BREATHER HOSE
  1. Install the fuel tank breather hose to the fuel tank.



3. INSTALL FUEL TANK VENT TUBE SUB-ASSEMBLY
  1. Apply a light coat of gasoline or grease to a new gasket and install the gasket to the fuel tank.

  1. Install the fuel tank vent tube to the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Set the fuel pump gauge retainer on the fuel tank. While holding the fuel tank vent tube, tighten the fuel pump gauge retainer one complete turn by hand.



    A246112E04
  1. Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.

    SST
    09808-14030  

    HINT:
    1. Hold the fuel tank vent tube sub-assembly upright by hand to make that the gasket is not moved out of position.
    2. Be sure to use 4 SST (claws) as shown in the illustration.
    3. Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.

  1. While pressing SST (claws) to the fuel pump gauge retainer ribs securely, install the 4 bolts.

    HINT:
    Install SST while pressing SST (claws) against the fuel pump gauge retainer (toward the center of SST).

  1. Install SST (handle).



    A241651E07
  1. Using SST, tighten the fuel pump gauge retainer until the mark on the fuel pump gauge retainer aligns with mark A on the fuel tank, as shown in the illustration.

    SST
    09808-14030  

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
    3. Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.
    4. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    5. If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.

    HINT:
    1. If the alignment is difficult, make sure the mark on the fuel pump gauge retainer is within range B on the fuel tank.
    2. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to tighten the fuel pump gauge retainer.
    3. The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.

  1. Install the fuel tank return tube and fuel tank main tube to the fuel tank.



  1. Install the 2 fuel tank tubes with the 2 tube joint clips.

    NOTICE:
    A118171E11
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.



4. INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    A197374
  1. Install the No. 1 fuel evaporation tube.



5. INSTALL FUEL TANK CUSHION


    A197373E01
  1. Install 4 new fuel tank cushions.



6. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A191330E01
  1. Install the No. 1 fuel tank protector with the 5 clips and 2 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



7. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank on a transmission jack and raise the fuel tank.

    NOTICE:
    Do not allow the fuel tank to contact the vehicle, especially the differential.



    A197454E01
  1. Fold back approximately half of each cushion so that the wire harness can be installed in the step below.



    A116060
  1. Attach the wire harness to the 4 clamps and connect the fuel pump and sender gauge connector.

    NOTICE:
    Be careful not to cut the wirings.

  1. Install the 3 fuel tank bands with the 3 pins and 3 clips.



    A191367
  1. Connect the 3 fuel tank bands with the 3 bolts.

    Torque:
    61 N*m{ 622 kgf*cm , 45 in.*lbf }



8. INSTALL FUEL TANK FILLER PIPE
  1. Install the filler pipe with the bolt and nut.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



9. CONNECT FUEL TANK TO FILLER PIPE HOSE


    A191366
  1. Connect the fuel tank to filler pipe hose to the fuel tank filler pipe.



10. CONNECT FUEL TANK BREATHER HOSE
  1. Attach the breather hose to the 2 clamps.

  1. Connect the fuel tank breather hose to the fuel tank filler pipe.



11. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE


    A197375
  1. Connect the fuel tank main tube and fuel tank return tube.



12. INSTALL FUEL TANK PROTECTOR


    A116046
  1. Install the fuel tank protector with the 4 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



13. INSTALL FUEL TANK CAP ASSEMBLY


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



15. BLEED AIR FROM FUEL SYSTEM
  1. w/o Glow Plug Controller:
  2. w/ Glow Plug Controller:


16. CHECK FOR FUEL LEAK
  1. w/o Glow Plug Controller:
  2. w/ Glow Plug Controller: