INTAKE MANIFOLD (w/ Glow Plug Controller) > INSTALLATION |
| 1. INSTALL INTAKE MANIFOLD |
![]() |
Temporarily install a new gasket and the intake manifold with the 4 bolts and 2 nuts.
Tighten the 4 bolts and 2 nuts in the order shown in the illustration.
Attach the sensor wire connector clamp.
| 2. INSTALL VACUUM SWITCHING VALVE ASSEMBLY |
![]() |
Install the No. 1 vacuum switching valve and No. 2 vacuum switching valve with the 2 screws.
| *1 | No. 1 vacuum switching valve |
| *2 | No. 2 vacuum switching valve |
| *a | Dark Blue Color |
| *b | Brown Color |
Connect the 4 vacuum hoses.
| 3. INSTALL VACUUM CONTROL VALVE SET |
![]() |
Install the vacuum control valve set with the 2 bolts.
| *1 | Paint Mark (White) |
| *2 | Paint Mark (Green) |
Connect the 3 vacuum hoses and 2 vacuum switching valve connectors.
| 4. INSTALL INTAKE MANIFOLD INSULATOR |
| 5. INSTALL NO. 1 INTAKE MANIFOLD INSULATOR |
| 6. INSTALL NO. 1 GLOW PLUG CONNECTOR |
Temporarily install the No. 1 glow plug connector with the 4 nuts.
Tighten the 4 nuts.
Install the 4 screw grommets.
| 7. INSTALL NO. 2 MANIFOLD STAY |
Install the No. 2 manifold stay with the bolt.
| 8. INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET |
Install the No. 3 intercooler support bracket with the bolt.
| 9. INSTALL GLOW CONNECTOR BRACKET |
Install the glow connector bracket with the bolt.
Connect the No. 1 glow plug connector and attach the clamp.
| 10. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.
![]() | Union Bolt |
Temporarily install a new gasket and the union bolt.
Tighten the 3 bolts and union bolt.
| 11. INSTALL NO. 3 NOZZLE LEAKAGE PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Temporarily install the No. 3 nozzle leakage pipe with the 2 bolts.
Temporarily install a new gasket and the fuel check valve.
Tighten the 2 bolts and fuel check valve.
Connect the 3 fuel hoses.
| 12. INSTALL NO. 2 FUEL PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Install a new gasket to the No. 2 fuel pipe and temporarily install the fuel check valve.
Temporarily install a new gasket and the supply pump hollow screw.
Using a 6 mm hexagon wrench, tighten the supply pump hollow screw.
Tighten the fuel check valve.
| 13. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the wiring harness clamp bracket with the bolt.
Attach the wire harness clamp.
| 14. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 No. 2 injection pipe clamps with the bolt and nut.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 15. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 18. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 19. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 20. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Intelligent Tester Display | Test Part | Control Range | Diagnostic Note |
| Test the Fuel Leak | Pressurize common rail interior and check for fuel leaks | Stop/Start |
|