Home › ENGINE ยท 1KD-FTV › FUEL › FUEL INJECTOR (w/ Glow Plug Controller)

FUEL INJECTOR (w/ Glow Plug Controller) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER
(Click here)


4. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY


    A271613
  1. Remove the bolt, nut and 2 No. 2 injection pipe clamps.



    A271614
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



5. REMOVE WIRING HARNESS CLAMP BRACKET


    A267354E01
  1. Detach the wire harness clamp.
    Text in Illustration 
    *1
    Wiring Harness Clamp Bracket

  1. Remove the bolt and wiring harness clamp bracket.



6. REMOVE NO. 2 FUEL PIPE


    A271615
  1. Using a 6 mm hexagon wrench, remove the supply pump hollow screw and gasket.
    Text in Illustration 
    V100135
    Supply Pump Hollow Screw
    V100136
    Fuel Check Valve

  1. Remove the fuel check valve, No. 2 fuel pipe and gasket.



7. REMOVE NO. 3 NOZZLE LEAKAGE PIPE


    A252280
  1. Disconnect the 3 fuel hoses.
    Text in Illustration 
    V100136
    Fuel Check Valve

  1. Remove the 2 bolts.

  1. Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.



8. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY


    A271661
  1. Remove the 3 bolts.
    Text in Illustration 
    V100136
    Union Bolt

  1. Remove the union bolt, gasket and No. 2 nozzle leakage pipe.



9. REMOVE WIRING HARNESS CLAMP BRACKET


    A271761
  1. Detach the 6 wire harness clamps.

  1. Remove the 3 bolts and 2 wiring harness clamp brackets.



10. REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY


    A252282
  1. Remove the 3 bolts and No. 2 cylinder head cover.



11. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.



    A060180E01
  1. Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.



    A223193
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.



    A289511
  1. Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.



12. REMOVE INJECTOR ASSEMBLY


    A271617E01
  1. Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A271618
  1. Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.