DTC P1603 Engine Stall History |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| - | 2 seconds or more elapse after starting the engine, and the engine running, the engine stops for 0.5 seconds or more without the ignition switch being operated (for Manual Transmission: Fuel pressure drops to 10000 kPa or less and fuel injection is stopped) (1 trip detection logic) |
|
| DTC No. | Data List |
| P1603 |
|
| Fuel system |
The following malfunctions may be present in the fuel system.
Problem with injector assemblies.
Problem with fuel supply pump assembly.
Air in fuel pipe.
Fuel filter element sub-assembly clog.
| Engine assembly |
The following malfunctions may be present in the engine assembly.
Insufficient compression.
![]() |
| 1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1)) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Record the stored DTC and freeze frame data.
| NEXT | |
| 2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P1603 is output | A |
| P1603 and other DTCs are output | B |
|
| ||||
| A | |
| 3.TAKE SNAPSHOT DURING IDLING (PROCEDURE 3) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine / Data List / Diesel Starting.
Take a snapshot when idling with no load after the engine is warmed up and when the problem is occurring.
| NEXT | |
| 4.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT) |
Determine the cause of the problem based on the freeze frame data recorded in procedure 1 and the Data List values recorded when idling the engine in procedure 3.
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| "Battery Voltage" in freeze frame data is below 6 V | Engine starting trouble may have occurred because battery is fully depleted | During cranking: 6 V or higher | The battery may be fully depleted or the battery terminals may be loose. |
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| "Fuel Press" in freeze frame data is below 25000 kPa (254.9 kgf/cm2, 3626 psi) | Problem supplying fuel to fuel supply pump assembly (low pressure side)
| When in a stable condition such as when the engine is idling after being warmed up, the fuel pressure is within +/-5000 kPa of the target fuel pressure
| If "Fuel Press" is 10000 kPa (102.0 kgf/cm2, 1451 psi) or less, fuel injection control is stopped.
|
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| "Injection Feedback Val #1 (to #4)" in freeze frame data is not +3.0 mm3/st or less | Injector assembly malfunction or compression problem | Less than +3.0 mm3/st | If an injector assembly is malfunctioning, even though the engine starts, idling is rough.
|
| "Injection Feedback Val #1 (to #4)" in Data List is not +3.0 mm3/st or less when idling |
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| "Injection Volume" in Data List is more than 12 mm3/st and "Injection Feedback Val #1 (to #4)" is within range of 3.0 mm3/st when idling after warming up engine | Injector assemblies of all cylinders malfunctioning | - |
|
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| Any values for "Injector Leaking Count #1 to #4" in the Freeze Frame Data display 1 or more |
| 0 | When the counter is 1 or more, the problem may have occurred due to foreign matter in the fuel system. Replace the fuel filter, etc. and perform repairs according to the troubleshooting procedure.
|
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| Any values for "i-ART Learning Status History #1 to #4" in the Freeze Frame Data display 1 Trip or more |
| 0 Trip | When the counter is 1 or more, the problem may have occurred due to foreign matter in the fuel system. Replace the fuel filter, etc. and perform repairs according to the troubleshooting procedure.
|
| Judgment of Data List Values | Problem Cause | Normal Condition | Diagnosis Note |
| "Immobiliser Fuel Cut History" in freeze frame data is OFF to ON | Fuel injection has stopped due to engine immobiliser system.
| OFF |
|
| NEXT | ||
| ||