ECD SYSTEM (for i-ART) > Fuel Injection System |
| 1.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 1) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Take a snapshot of the following Data List items.
| NEXT | |
| 2.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME) |
Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken in procedure 1 when the engine was idling and at 4000 rpm with no load.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st | A |
| Injection Volume is 10 mm3/st or less at 4000 rpm | B |
| Except above | C |
|
| ||||
|
| ||||
| C | |
| 3.READ VALUE USING GTS (INJECTION VOLUME) |
Check Injection Volume in the snapshot taken in procedure 1 when the engine was idling.
| Result | Proceed to |
| Injection Volume while idling after engine warm up is 12 mm3/st or more | A |
| Except above | B |
|
| ||||
| B | |
| 4.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 1 when the engine was idling and at 4000 rpm.
| Result | Proceed to |
| The value for Injector Leaking Count #1 to #4 does not change from 0 The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip | A |
| The value for Injector Leaking Count #1 to #4 displays 1 or more The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more | B |
|
| ||||
|
| ||||
| 5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
| Result | Proceed to |
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. | B |
|
| ||||
| A | |
| 6.CHECK CYLINDER COMPRESSION PRESSURE |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 7.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 1 when the engine was idling and at 4000 rpm.
Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
| NEXT | |
| 8.REPLACE INJECTOR ASSEMBLY |
Replace the injector assembly of the malfunctioning cylinder (Click here).
|
| ||||
| 9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
|
| ||||
| 10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS |
Replace the injector assemblies of all cylinders (Click here).
| NEXT | |
| 11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 12.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
|
| ||||
| 13.CHECK AND REPLACE ENGINE ASSEMBLY |
Check and replace the engine assembly.
| NEXT | |
| 14.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.
Start the engine.
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

| Result | Proceed to |
| NG | A |
| OK* | B |
|
| ||||
| A | |
| 15.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE) |
Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check .
Select "Always Closed Check".
Press "Next".
Read the value for the fuel pressure.
|
| ||||
| OK | |
| 16.INSPECT CLOGGED FUEL PIPE |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Injection.
With no load after the engine is warmed up, take a snapshot when idling and while the vehicle is accelerating with the accelerator pedal fully depressed in 2nd gear.
Check the Target Common Rail Pressure and Fuel Press value.

| Result | Proceed to |
| While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 | A |
| "Fuel Press" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2 | |
| Except above | B |
|
| ||||
| A | |
| 17.REPAIR OR REPLACE CLOGGED FUEL LINE |
Repair or replace the clogged (including frozen fuel) fuel pipe.
Replace the fuel filter element sub-assembly.
|
| ||||
| 18.REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE) |
Replace the common rail assembly (Click here).
| NEXT | |
| 19.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 20.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Check Fuel Press and Target Common Rail Pressure in the snapshot taken in procedure 1 when the engine was idling.
| Result | Proceed to |
| Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more | B |
| Except above | A |
|
| ||||
| B | |
| 21.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE) |
Replace the fuel supply pump assembly (Click here).
| NEXT | |
| 22.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 23.PERFORM SUPPLY PUMP INITIALIZATION |
Perform supply pump initialization (Click here).
| NEXT | |
| 24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||