DTC P042E Exhaust Gas Recirculation "A" Control Stuck Open |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After warming up engine and idling for 60 seconds, maintain engine speed at 2500 rpm for 40 seconds, drive vehicle, and perform engine brake deceleration by fully closing accelerator when engine speed is 2000 rpm or more. | The target and actual positions of the EGR valve are different for 20 seconds or more. (1 trip detection logic) |
|
| While the engine is running, the EGR activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more). (1 trip detection logic) |
| DTC No. | Data List |
| P042E |
|


| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042E) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P042E is output | A |
| P042E and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Target EGR Position and Actual EGR Valve Pos.
When changing the Active Test value for 0, 25, 50, 75 and 100%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Remove the electric EGR control valve assembly (Click here).
Reconnect the electric EGR control valve assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position.
Check if the valve of the electric EGR control valve assembly opens/closes when an Active Test is performed.
![]() |
Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.
| Result | Proceed to |
| NG | A |
| OK | B |
| *1 | Gap |
| *a | OK |
| *b | NG |
Reinstall the electric EGR control valve assembly (Click here).
|
| ||||
| A | |
| 4.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Replace the electric EGR control valve assembly (Click here).
|
| ||||
| 5.CHECK FOR DEPOSIT |
Remove the electric EGR control valve assembly (Click here).
Visually check the electric EGR control valve assembly for deposits.
If there are deposits, clean the electric EGR control valve assembly.
Reinstall the electric EGR control valve assembly (Click here).
| NEXT | |
| 6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
After warming up the engine and idling for 60 seconds, maintain the engine speed at 2500 rpm for 40 seconds, drive the vehicle, and perform engine brake deceleration by fully closing the accelerator when the engine speed is 2000 rpm or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||