Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    3. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    C236338E04


    Text in Illustration 
    *a
    for No. 2 Junction Connector
    *b
    for ECM (V Bus)
    *c
    for Brake Actuator Assembly (Skid Control ECU)
    -
    -

    No. 1 Junction Connector
    Wiring Color
    Connect to
    J64-4 (CANH)
    B
    No. 2 junction connector
    J64-1 (CANL)
    W
    J64-12 (CANH)
    B
    ECM (V bus)
    J64-6 (CANL)
    W
    J64-13 (CANH)
    R
    Brake actuator assembly (skid control ECU)
    J64-7 (CANL)
    W



  2. NO. 2 JUNCTION CONNECTOR


    C240979E03


    Text in Illustration 
    *a
    for No. 1 Junction Connector
    *b
    for No. 3 Junction Connector
    *c
    for Yaw Rate Sensor Assembly
    -
    -

    No. 2 Junction Connector
    Wiring Color
    Connect to
    J65-5 (CANH)
    B
    No. 1 junction connector
    J65-16 (CANL)
    W
    J65-6 (CANH)
    B
    No. 3 junction connector
    J65-17 (CANL)
    W
    J65-7 (CANH)
    R
    Yaw rate sensor assembly
    J65-18 (CANL)
    W



  3. NO. 3 JUNCTION CONNECTOR


    C236340E04


    Text in Illustration 
    *1
    No. 3 Junction Connector
    *2
    Junction Connector A Side
    *3
    Junction Connector B Side
    -
    -
    *a
    Ground Terminal
    -
    -

    Junction Connector A Side
    Wiring Color (CANH Side)
    Wiring Color (CANL Side)
    DLC3 (J52)
    R
    W

    Junction Connector B Side
    Wiring Color (CANH Side)
    Wiring Color (CANL Side)
    No. 2 Junction Connector (J53)
    B
    W
    Spiral Cable Sub-assembly (Steering Angle Sensor) (J63)
    R
    W


CHECK DLC3


    C201374E98
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D3-6 (CANH) - D3-14 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D3-6 (CANH) - D3-4 (CG)
    R - G
    Ignition switch off
    200 Ω or higher
    D3-14 (CANL) - D3-4 (CG)
    W - G
    Ignition switch off
    200 Ω or higher
    D3-6 (CANH) - D3-16 (BAT)
    R - G
    Ignition switch off
    6 kΩ or higher
    D3-14 (CANL) - D3-16 (BAT)
    W - G
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV)

C236400E04


Text in Illustration 
*A
for V Bus
*B
for Powertrain Bus
  1. Disconnect the E5 and E6 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E5-24 (CANH) - E5-23 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E5-24 (CANH) - E6-7 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E5-23 (CANL) - E6-7 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E5-24 (CANH) - E5-2 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E5-23 (CANL) - E5-2 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher

    for Powertrain Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E5-22 (CAN+) - E5-21 (CAN-)
    V - P
    Ignition switch off
    108 to 132 Ω
    E5-22 (CAN+) - E6-7 (E1)
    V - BR
    Ignition switch off
    200 Ω or higher
    E5-21 (CAN-) - E6-7 (E1)
    P - BR
    Ignition switch off
    200 Ω or higher
    E5-22 (CAN+) - E5-2 (BATT)
    V - L
    Ignition switch off
    6 kΩ or higher
    E5-21 (CAN-) - E5-2 (BATT)
    P - L
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1GR-FE)

G036662E36

  1. Disconnect the E13, E14 and E17 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E13-33 (CANH) - E13-34 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E13-33 (CANH) - E17-1 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E13-34 (CANL) - E17-1 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E13-33 (CANH) - E14-3 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E13-34 (CANL) - E14-3 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
C227479E09
  1. Disconnect the S25 brake actuator assembly (skid control ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S25-25 (CANH) - S25-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    S25-25 (CANH) - S25-1 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    S25-14 (CANL) - S25-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S25-25 (CANH) - S25-12 (+BS)
    B - W-R
    Ignition switch off
    6 kΩ or higher
    S25-14 (CANL) - S25-12 (+BS)
    W - W-R
    Ignition switch off
    6 kΩ or higher


CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)
C223167E10
  1. Disconnect the S31 spiral cable sub-assembly (steering angle sensor) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S31-4 (CANH) - S31-3 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    S31-4 (CANH) - S31-2 (ESS)
    R - W-B
    Ignition switch off
    200 Ω or higher
    S31-3 (CANL) - S31-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S31-4 (CANH) - S31-6 (BAT)
    R - B
    Ignition switch off
    6 kΩ or higher
    S31-3 (CANL) - S31-6 (BAT)
    W - B
    Ignition switch off
    6 kΩ or higher


CHECK YAW RATE SENSOR ASSEMBLY

C213562E16

  1. Disconnect the Y1 yaw rate sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    Y1-3 (CANH) - Y1-1 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    Y1-2 (CANL) - Y1-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    Y1-3 (CANH) - D3-16 (BAT)
    B - G
    Ignition switch off
    6 kΩ or higher
    Y1-2 (CANL) - D3-16 (BAT)
    W - G
    Ignition switch off
    6 kΩ or higher


CHECK TRANSMISSION CONTROL ECU ASSEMBLY (TCM) (for 1kD-FTV and Automatic Transmission)

C236432E03

  1. Disconnect the T19 and T35 transmission control ECU assembly (TCM) connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    T35-21 (CAN+) - T35-20 (CAN-)
    V - P
    Ignition switch off
    108 to 132 Ω
    T35-21 (CAN+) - T19-1 (E1)
    V - BR
    Ignition switch off
    200 Ω or higher
    T35-20 (CAN-) - T19-1 (E1)
    P - BR
    Ignition switch off
    200 Ω or higher
    T35-21 (CAN+) - T35-5 (BATT)
    V - L
    Ignition switch off
    6 kΩ or higher
    T35-20 (CAN-) - T35-5 (BATT)
    P - L
    Ignition switch off
    6 kΩ or higher