CAN COMMUNICATION SYSTEM (w/ VSC) > Open in CAN Main Bus Line |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher. |
|

| 1.PRECAUTION |
| NEXT | |
| 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
| NEXT | |
| 3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DLC3) |
![]() |
Disconnect the J52 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J52-2 (CANH) - G18-6 (CANH) | Ignition switch off | Below 1 Ω |
| J52-1 (CANL) - G18-14 (CANL) | Ignition switch off | Below 1 Ω |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 4.CONNECT CONNECTOR |
Reconnect the J52 No. 3 junction connector.
| NEXT | |
| 5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Disconnect the J64 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J64-12 (CANH) - J64-6 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | |
| 6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J64-4 (CANH) - J64-1 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 7.CONNECT CONNECTOR |
Reconnect the J64 No. 1 junction connector.
| NEXT | |
| 8.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 JUNCTION CONNECTOR) |
Disconnect the E13*1, E5*2 or E31*3 ECM connector.

| *A | for 1GR-FE | *B | for 1KD-FTV |
| *C | for 1KD-FTV (w/ i-ART) | - | - |
| *a | Front view of wire harness connector (to ECM) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E13-33 (CANH) - E13-34 (CANL) | Ignition switch off | 108 to 132 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| E5-24 (CANH) - E5-23 (CANL) | Ignition switch off | 108 to 132 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| E31-35 (CANH) - E31-36 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| OK (for 1GR-FE) | A |
| OK (for 1KD-FTV [w/ Glow Plug Controller]) | B |
| OK (for 1KD-FTV [w/o Glow Plug Controller]) | C |
| NG | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 9.CONNECT CONNECTOR |
Reconnect the J64 No. 1 junction connector.
| NEXT | |
| 10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR) |
![]() |
Disconnect the J65 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J65-5 (CANH) - J65-16 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J65-6 (CANH) - J65-17 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 12.CONNECT CONNECTOR |
Reconnect the J65 No. 2 junction connector.
| NEXT | |
| 13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the J53 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J53-2 (CANH) - J53-1 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 3 Junction Connector) |
|
| ||||
| OK | ||
| ||