Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Open in CAN Main Bus Line

for Preparation Click here


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. No. 3 junction connector
  5. ECM
  6. DLC3 CAN branch wire or connector

WIRING DIAGRAM


C240997E05


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DLC3)


    C241015E02
  1. Disconnect the J52 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J52-2 (CANH) - G18-6 (CANH)
    Ignition switch off
    Below 1 Ω
    J52-1 (CANL) - G18-14 (CANL)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J52 No. 3 junction connector.


NEXT


5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C236390E10
  1. Disconnect the J64 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J64-12 (CANH) - J64-6 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 7
OK


6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C236390E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J64-4 (CANH) - J64-1 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 9
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

7.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


8.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 JUNCTION CONNECTOR)


  1. Disconnect the E13*1, E5*2 or E31*3 ECM connector.


    C275226E01


    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 1KD-FTV
    *C
    for 1KD-FTV (w/ i-ART)
    -
    -
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -
    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for 1KD-FTV (w/ i-ART)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    E13-33 (CANH) - E13-34 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    E5-24 (CANH) - E5-23 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1KD-FTV (w/ i-ART) 
    Tester Connection
    Switch Condition
    Specified Condition
    E31-35 (CANH) - E31-36 (CANL)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1KD-FTV [w/ Glow Plug Controller])
    B
    OK (for 1KD-FTV [w/o Glow Plug Controller])
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 1 JUNCTION CONNECTOR)
A

REPLACE ECM (Click here)  

9.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    C224479E99
  1. Disconnect the J65 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J65-5 (CANH) - J65-16 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C247209E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J65-6 (CANH) - J65-17 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 12
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

12.CONNECT CONNECTOR
  1. Reconnect the J65 No. 2 junction connector.


NEXT


13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C236882E09
  1. Disconnect the J53 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J53-2 (CANH) - J53-1 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR