Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Short in CAN Bus Lines

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Brake actuator assembly (skid control ECU)
  4. Spiral cable sub-assembly (steering angle sensor)
  5. Yaw rate sensor assembly
  6. No. 1 junction connector
  7. No. 2 junction connector
  8. No. 3 junction connector

WIRING DIAGRAM


C247094E02


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR SHORT IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)


    C241015E02
  1. Disconnect the J52 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J52-2 (CANH) - D3-6 (CANH)
    Ignition switch off
    Below 1 Ω
    J52-1 (CANL) - D3-14 (CANL)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J52 No. 3 junction connector.


NEXT


5.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    C201374E95
  1. Disconnect the J64 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-6 (CANH) - D3-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 12
OK


6.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C236390E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J64-13 (CANH) - J64-7 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 8
OK


7.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C236390E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J64-12 (CANH) - J64-6 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 10
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


9.CHECK FOR SHORT IN CAN BUS WIRE (SKID CONTROL ECU)


    C234968E21
  1. Disconnect the S25 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S25-25 (CANH) - S25-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTRO ECU) (Click here)  

10.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


11.CHECK FOR SHORT IN CAN BUS WIRE (ECM)


  1. Disconnect the E13*1, E5*2 or E31*3 ECM connector.


    C275226E01


    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 1KD-FTV
    *C
    for 1KD-FTV (w/ i-ART)
    -
    -
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -
    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for 1KD-FTV (w/ i-ART)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    E13-33 (CANH) - E13-34 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    E5-24 (CANH) - E5-23 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1KD-FTV (w/ i-ART) 
    Tester Connection
    Switch Condition
    Specified Condition
    E31-35 (CANH) - E31-36 (CANL)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1KD-FTV [w/ Glow Plug Controller])
    B
    OK (for 1KD-FTV [w/o Glow Plug Controller])
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

12.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


13.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    C224479E99
  1. Disconnect the J65 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J65-5 (CANH) - J65-16 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


14.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    C201374E95
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-6 (CANH) - D3-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 18
OK


15.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)


    C247209E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J65-7 (CANH) - J65-18 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 16
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

16.CONNECT CONNECTOR
  1. Reconnect the J65 No. 2 junction connector.


NEXT


17.CHECK FOR SHORT IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)


    C222816E15
  1. Disconnect the Y1 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)  

18.CONNECT CONNECTOR
  1. Reconnect the J65 No. 2 junction connector.


NEXT


19.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C236882E09
  1. Disconnect the J53 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J53-2 (CANH) - J53-1 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


20.CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C236882E08
  1. Disconnect the J63 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J63-2 (CANH) - J63-1 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 21
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

21.CONNECT CONNECTOR
  1. Reconnect the J53 and J63 No. 3 junction connectors.


NEXT


22.CHECK FOR SHORT IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C234977E10
  1. Disconnect the S31 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S31-4 (CANH) - S31-3 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)