CAN COMMUNICATION SYSTEM (w/ VSC) > DIAGNOSIS SYSTEM |
| BUS CHECK (COMMUNICATION MALFUNCTION ECU) |
![]() |
Select "Bus Check" from the "System Select" screen on the intelligent tester.
![]() |
Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".
![]() |
Select the system of the DTC to be checked and select "Details".
![]() |
CAN communication system DTCs are output.
| BUS CHECK (COMMUNICATION BUS CHECK) |
![]() |
Select "Communication Bus Check" from the "Bus Check" screen.
The screen displays the ECUs and sensors that are properly connected to the CAN communication system.
| Combo Box | Display Content |
| ALL | All ECUs (sensors) connected to the CAN bus |
| V Bus | ECUs (sensors) connected to the V Bus |
| Bus Name | ECUs (sensors) connected to the selected bus |
| Background Color | Connection Status |
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Not displayed | Has never been detected |
| Background Color | Connection Status |
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Not displayed | Has never been detected |
| Background Color | Connection Status |
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Red | Has never been detected but has connection history |
| Not displayed | Has never been detected |
![]() |
"There is no system connected to the communication bus." is displayed if there are no ECUs or sensors connected to the CAN bus.
| CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION |
Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.
| ECU/Sensor Name | Tester Display | Installed on |
| ECM | ECM (Engine) | All vehicles |
| Transmission control ECU assembly (TCM) | TCM | for 1KD-FTV and Automatic Transmission |
| Brake actuator assembly (skid control ECU) | Skid Control (ABS/VSC/TRAC) | All vehicles |
| Yaw rate sensor assembly | Yaw Rate Sensor | All vehicles |
| Spiral cable sub-assembly (steering angle sensor) | Spiral cable (Steering Angle Sensor) | All vehicles |
| DTC TABLE BY ECU |
ECM
| DTC Code | Detection Item |
| U0101* | Lost Communication with TCM |
TRANSMISSION CONTROL ECU ASSEMBLY (TCM)
| DTC Code | Detection Item |
| U0100* | Lost Communication with ECM/PCM "A" |
BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
| DTC Code | Detection Item |
| U0073 | Control Module Communication Bus Off |
| U0100 | Lost Communication with ECM/PCM "A" |
| U0123 | Lost Communication with Yaw Rate Sensor Module |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module |
| U0126 | Lost Communication with Steering Angle Sensor Module |
YAW RATE SENSOR ASSEMBLY
SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)
| DTC COMBINATION TABLE |
| Output from | Output DTC | Detection Item | Detected Communication Stop Mode | |||
| V Bus | ||||||
| Skid Control ECU Communication Stop Mode | Yaw Rate Sensor Communication Stop Mode | Steering Angle Sensor Communication Stop Mode | ECM Communication Stop Mode | |||
| Brake actuator assembly (skid control ECU) | U0073 | Control Module Communication Bus Off | ○ | - | - | - |
| U0100 | Lost Communication with ECM/PCM "A" | ○ | - | - | ○ | |
| U0123 | Lost Communication with Yaw Rate Sensor Module | ○ | ○ | - | - | |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module | ○ | ○ | - | - | |
| U0126 | Lost Communication with Steering Angle Sensor Module | ○ | - | ○ | - | |