Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM33K0E _52 Drivetrain _043526 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0211496 SHIFT LEVER A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RH and LH vehicles.

·

The procedure listed below is for LH vehicles.



PROCEDURE

Hide 33550 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

NOTICE:

Check that the park/neutral position switch assembly and the shift lever are in N.


a.

Install the transmission floor shift assembly to the vehicle body with the 4 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Attach the 3 wire harness clamps and connect the wire harness to the transmission floor shift assembly.


c.

Connect the 2 connectors to the transmission floor shift assembly.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C326297C01
1.823,2.583 2.052,2.313 2.052,2.313 2.208,2.313 true 2.271,2.219 2.583,2.375 0.313,0.156 10 false *1 0.313,0.063 0.625,0.219 0.313,0.156 10 false *a 0.323,1 0.635,1.156 0.313,0.156 10 false *b 2.177,0 2.49,0.156 0.313,0.156 10 false *c 0.323,2.396 0.635,2.552 0.313,0.156 10 false *a 1.135,0 1.448,0.156 0.313,0.156 10 false *c 1.635,0.885 1.948,1.042 0.313,0.156 10 false *c 1.5,1.833 1.813,1.99 0.313,0.156 10 false *c
*1 Lock Piece
*a Side View
*b Bottom View
*c Push


Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.


b.
C324385C02
2.917,0.917 2.917,0.417 2.917,0.417 3.083,0.417 false 3.125,0.344 3.354,0.531 0.229,0.188 10 false *1
*1 Lock Piece
V113147

Connect in this Direction


Connect the transmission control cable assembly to the transmission floor shift assembly, and install a new clip.


c.

Connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

The shift lever should be in N.

·

Make sure that the lock piece is pulled up.

·

Push on the end of the cable all the way to the base of the transmission floor shift assembly pin.




d.
C326299C01
1.74,0.469 1.896,0.167 1.896,0.167 2.042,0.167 true 2.167,0.688 2.323,0.385 2.323,0.385 2.469,0.385 true 2.083,0.083 2.396,0.24 0.313,0.156 10 false *1 2.521,0.302 2.833,0.458 0.313,0.156 10 false *2 1.594,1.896 1.906,2.052 0.313,0.156 10 false *a
*1 Lock Piece
*2 Adjuster Case
*a Push


Push the lock piece into the adjuster case.

NOTICE:

Securely push in the lock piece until it locks.



Hide 58861B 4.INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Air Duct)

a.

Install the No. 1 console box duct with the 2 clips.