Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0218826 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost
·

Radio and display receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

Harness or connector



WIRING DIAGRAM

E322157E01
0.948,1.073 1.708,1.719 0.76,0.646 10 false Telephone Microphone Assembly 2.135,0.958 3.542,1.604 1.406,0.646 10 false MCO+ 2.156,1.406 3.563,2.052 1.406,0.646 10 false MCO- 2.156,1.917 2.667,2.427 0.51,0.51 10 false MACC 2.656,1.938 3.167,2.448 0.51,0.51 10 false 15 2.656,1.458 3.167,1.969 0.51,0.51 10 false 13 2.656,0.948 3.167,1.458 0.51,0.51 10 false 14 0.688,3.396 2.094,4.042 1.406,0.646 10 false Q2 0.688,3.531 2.094,4.177 1.406,0.646 10 false Map Light Assembly 5.625,0.99 6.135,1.5 0.51,0.51 10 false 5 5.552,1.458 6.063,1.969 0.51,0.51 10 false 19 5.552,2.396 6.063,2.906 0.51,0.51 10 false 18 5.615,1.938 6.125,2.448 0.51,0.51 10 false 4 5.865,1.063 6.885,1.688 1.021,0.625 10 false MIN+ 5.854,1.521 6.875,2.146 1.021,0.625 10 false MIN- 5.844,2.021 6.354,2.531 0.51,0.51 10 false MACC 5.833,2.49 6.344,3 0.51,0.51 10 false SGND 5.698,3.521 7,4.125 1.302,0.604 10 false G100 5.698,3.688 7,4.292 1.302,0.604 10 false Radio and Display Receiver Assembly 0.396,4.365 1.969,4.719 1.573,0.354 10 false *: Shielded 3.563,2.677 3.813,3.198 0.25,0.521 10 false * 4.781,2.656 5.031,3.177 0.25,0.521 10 false *

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G100 radio and display receiver assembly connector.


b.

Disconnect the Q2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-4 (MACC) - Q2-15 (MACC) Always Below 1 Ω
G100-5 (MIN+) - Q2-14 (MCO+) Always Below 1 Ω
G100-19 (MIN-) - Q2-13 (MCO-) Always Below 1 Ω
G100-18 (SGND) - Body ground Always 10 kΩ or higher
G100-4 (MACC) or Q2-15 (MACC) - Body ground Always 10 kΩ or higher
G100-5 (MIN+) or Q2-14 (MCO+) - Body ground Always 10 kΩ or higher
G100-19 (MIN-) or Q2-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E316674C04
1.49,0.667 1.958,0.917 0.469,0.25 2.604,2.51 2.427,2.51 2.427,2.51 2.063,1.979 true 2.802,1.01 2.625,1.01 2.625,1.01 2.208,1.75 true 0.135,0.177 0.448,0.333 0.313,0.156 10 false *a 1.552,0.719 2.198,0.865 0.646,0.146 10 false G100 2.885,0.896 3.417,1.135 0.531,0.24 10 false MACC 2.667,2.375 3.198,2.615 0.531,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-19 (MIN-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G100-4 (MACC) - Body ground Ignition switch ON 4 to 6 V



Result:
Proceed to
OK
NG



OK

3.CHECK MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK MAP LIGHT ASSEMBLY
a.
E316675C01
0.26,0.729 0.708,1 0.448,0.271 0.615,1.729 0.813,1.729 0.813,1.729 1.438,1.219 true 2.604,1.917 2.354,1.917 2.354,1.917 1.594,1.208 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.385,0.75 0.698,0.948 0.313,0.198 10 false Q2 2.677,1.781 3.25,2 0.573,0.219 10 false MCO- 0.177,1.594 0.75,1.813 0.573,0.219 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Reconnect the map light assembly with the connector still connected.


b.

Turn the ignition switch to ACC.


c.

Connect an oscilloscope to terminals Q2-14 (MCO+) and Q2-13 (MCO-) of the map light assembly connector.


d.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is not output. A
A waveform synchronized with the voice input to the map light assembly is output. B



A

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG