Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0218826 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.


WIRING DIAGRAM

E322157E01
0.948,1.073 1.708,1.719 0.76,0.646 10 false Telephone Microphone Assembly 2.135,0.958 3.542,1.604 1.406,0.646 10 false MCO+ 2.156,1.406 3.563,2.052 1.406,0.646 10 false MCO- 2.156,1.917 2.667,2.427 0.51,0.51 10 false MACC 2.656,1.938 3.167,2.448 0.51,0.51 10 false 15 2.656,1.458 3.167,1.969 0.51,0.51 10 false 13 2.656,0.948 3.167,1.458 0.51,0.51 10 false 14 0.688,3.396 2.094,4.042 1.406,0.646 10 false Q2 0.688,3.531 2.094,4.177 1.406,0.646 10 false Map Light Assembly 5.625,0.99 6.135,1.5 0.51,0.51 10 false 5 5.552,1.458 6.063,1.969 0.51,0.51 10 false 19 5.552,2.396 6.063,2.906 0.51,0.51 10 false 18 5.615,1.938 6.125,2.448 0.51,0.51 10 false 4 5.865,1.063 6.885,1.688 1.021,0.625 10 false MIN+ 5.854,1.521 6.875,2.146 1.021,0.625 10 false MIN- 5.844,2.021 6.354,2.531 0.51,0.51 10 false MACC 5.833,2.49 6.344,3 0.51,0.51 10 false SGND 5.698,3.521 7,4.125 1.302,0.604 10 false G100 5.698,3.688 7,4.292 1.302,0.604 10 false Radio and Display Receiver Assembly 0.396,4.365 1.969,4.719 1.573,0.354 10 false *: Shielded 3.563,2.677 3.813,3.198 0.25,0.521 10 false * 4.781,2.656 5.031,3.177 0.25,0.521 10 false *

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E309166

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.


c.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

Voice can be recorded for up to 5 seconds.




d.

Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

OK:

All check results are normal.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G100 radio and display receiver assembly connector.


b.

Disconnect the Q2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-4 (MACC) - Q2-15 (MACC) Always Below 1 Ω
G100-5 (MIN+) - Q2-14 (MCO+) Always Below 1 Ω
G100-19 (MIN-) - Q2-13 (MCO-) Always Below 1 Ω
G100-18 (SGND) - Body ground Always 10 kΩ or higher
G100-4 (MACC) or Q2-15 (MACC) - Body ground Always 10 kΩ or higher
G100-5 (MIN+) or Q2-14 (MCO+) - Body ground Always 10 kΩ or higher
G100-19 (MIN-) or Q2-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E316674C04
1.49,0.667 1.958,0.917 0.469,0.25 2.604,2.51 2.427,2.51 2.427,2.51 2.063,1.979 true 2.802,1.01 2.625,1.01 2.625,1.01 2.208,1.75 true 0.135,0.177 0.448,0.333 0.313,0.156 10 false *a 1.552,0.719 2.198,0.865 0.646,0.146 10 false G100 2.885,0.896 3.417,1.135 0.531,0.24 10 false MACC 2.667,2.375 3.198,2.615 0.531,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-19 (MIN-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G100-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

4.CHECK MAP LIGHT ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK MAP LIGHT ASSEMBLY
a.
E316675C01
0.26,0.729 0.708,1 0.448,0.271 0.615,1.729 0.813,1.729 0.813,1.729 1.438,1.219 true 2.604,1.917 2.354,1.917 2.354,1.917 1.594,1.208 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.385,0.75 0.698,0.948 0.313,0.198 10 false Q2 2.677,1.781 3.25,2 0.573,0.219 10 false MCO- 0.177,1.594 0.75,1.813 0.573,0.219 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Reconnect the map light assembly with the connector still connected.


b.

Turn the ignition switch to ACC.


c.

Connect an oscilloscope to terminals Q2-14 (MCO+) and Q2-13 (MCO-) of the map light assembly connector.


d.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is not output. A
A waveform synchronized with the voice input to the map light assembly is output. B



A

5.CHECK TELEPHONE MICROPHONE ASSEMBLY

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

OK:

Malfunction does not recur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG