Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0218827 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.


WIRING DIAGRAM

E323304E02
0.948,0.615 1.688,1.125 0.74,0.51 10 false Telephone Microphone Assembly 2.125,0.521 2.646,0.76 0.521,0.24 10 false MCO+ 2.156,1.156 2.677,1.396 0.521,0.24 10 false MCO- 2.135,1.781 2.656,2.021 0.521,0.24 10 false MACC 2.625,0.531 3.146,0.771 0.521,0.24 10 false 14 2.646,1.146 3.167,1.385 0.521,0.24 10 false 13 2.646,1.771 3.167,2.01 0.521,0.24 10 false 15 0.729,2.927 1.25,3.167 0.521,0.24 10 false Q2 0.729,3.083 2.073,3.302 1.344,0.219 10 false Map Light Assembly 5.542,0.531 6.063,0.771 0.521,0.24 10 false 5 5.521,1.135 6.042,1.375 0.521,0.24 10 false 19 5.552,1.76 6.073,2 0.521,0.24 10 false 4 5.521,2.375 6.042,2.615 0.521,0.24 10 false 18 5.823,0.635 6.344,0.875 0.521,0.24 10 false MIN+ 5.823,1.24 6.344,1.479 0.521,0.24 10 false MIN- 5.833,1.865 6.354,2.104 0.521,0.24 10 false MACC 5.823,2.479 6.344,2.719 0.521,0.24 10 false SGND 5.521,2.948 6.042,3.188 0.521,0.24 10 false G108 5.542,3.104 7.156,3.302 1.615,0.198 10 false Radio Receiver Assembly 3.313,2.625 3.927,2.781 0.615,0.156 10 false Shielded 4.542,2.635 5.156,2.792 0.615,0.156 10 false Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G108 radio receiver assembly connector.


b.

Disconnect the Q2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-4 (MACC) - Q2-15 (MACC) Always Below 1 Ω
G108-5 (MIN+) - Q2-14 (MCO+) Always Below 1 Ω
G108-19 (MIN-) - Q2-13 (MCO-) Always Below 1 Ω
G108-18 (SGND) - Body ground Always 10 kΩ or higher
G108-4 (MACC) or Q2-15 (MACC) - Body ground Always 10 kΩ or higher
G108-5 (MIN+) or Q2-14 (MCO+) - Body ground Always 10 kΩ or higher
G108-19 (MIN-) or Q2-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO RECEIVER ASSEMBLY
a.
E316674C05
1.49,0.667 1.958,0.917 0.469,0.25 2.604,2.51 2.427,2.51 2.427,2.51 2.063,1.979 true 2.802,1.01 2.625,1.01 2.625,1.01 2.208,1.75 true 0.135,0.177 0.448,0.333 0.313,0.156 10 false *a 1.552,0.708 2.094,0.854 0.542,0.146 10 false G108 2.885,0.896 3.417,1.135 0.531,0.24 10 false MACC 2.667,2.375 3.198,2.615 0.531,0.24 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Remove the radio receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-19 (MIN-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G108-4 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V



Result:
Proceed to
OK
NG



OK

3.CHECK MAP LIGHT ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

3.CHECK MAP LIGHT ASSEMBLY
a.
E316675C01
0.26,0.729 0.708,1 0.448,0.271 0.615,1.729 0.813,1.729 0.813,1.729 1.438,1.219 true 2.604,1.917 2.354,1.917 2.354,1.917 1.594,1.208 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.385,0.75 0.698,0.948 0.313,0.198 10 false Q2 2.677,1.781 3.25,2 0.573,0.219 10 false MCO- 0.177,1.594 0.75,1.813 0.573,0.219 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with its connectors still connected.



b.

Turn the engine switch on (ACC).


c.

Connect an oscilloscope to terminals Q2-14 (MCO+) and Q2-13 (MCO-) of the map light assembly connector.


d.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output. A
A waveform synchronized with the voice input to the map light assembly is not output. B



A

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

B

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

OK:

Malfunction does not recur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG