Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM33K0E _58 Vehicle Interior _043552 SUPPLEMENTAL RESTRAINT SYSTEMS _0219474 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL SPIRAL CABLE (w/ Steering Sensor)

NOTICE:

If the steering sensor is installed to a misaligned spiral cable, DTCs for an abnormal steering sensor value such as DTC C1290, C1439 are stored and it is impossible to repair them. If this happens, replace the spiral cable sub-assembly with a new one.


a.
B415863C01
0.51,2.563 0.906,2.927 0.396,0.365 0.865,2.146 1.24,2.292 true 1.281,2.219 1.594,2.375 0.313,0.156 10 false *a 0.531,2.573 0.729,2.771 0.198,0.198 10 true *b
*a Check Window
*b Matchmark
V100144

U-Turn Point


Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

NOTICE:

When the conditions above cannot be checked via the check window with the front wheels facing straight ahead, there may be a malfunction in the spiral cable. In this case, replace the spiral cable sensor sub-assembly with a new one.



b.

If the spiral cable is not centered, center it.

i.
B415865C01
0,0 0,0 false
V100145

Interlock
V113147

Counterclockwise


While pushing on the interlock indicated in the illustration, rotate the spiral cable counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable using the airbag wire harness.




ii.
B415866C01
0,0 0,0 false
V100145

Interlock
V113147

Clockwise


While pushing on the interlock indicated in the illustration, rotate the spiral cable 2.5 times clockwise from the lock position.

HINT:

The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



iii.
B415863C01
0.51,2.563 0.906,2.927 0.396,0.365 0.865,2.146 1.24,2.292 true 1.281,2.219 1.594,2.375 0.313,0.156 10 false *a 0.531,2.573 0.729,2.771 0.198,0.198 10 true *b
*a Check Window
*b Matchmark
V100144

U-Turn Point


Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

NOTICE:

When the conditions above cannot be checked via the check window with the front wheels facing straight ahead, there may be a malfunction in the spiral cable. In this case, replace the spiral cable sub-assembly with a new one.




c.
B415880C01
1.51,1.75 1.771,1.75 1.771,1.75 2,1.823 true 2.635,2.927 2.51,2.188 true 0.708,2.198 1.229,2.198 true 1.333,1.635 1.646,1.792 0.313,0.156 10 false *a 0.74,0.677 0.917,0.865 0.177,0.188 10 true *b 0.542,2.094 0.854,2.25 0.313,0.156 10 false *c 0.552,1.292 0.729,1.479 0.177,0.188 10 true *b 2.583,2.958 2.896,3.115 0.313,0.156 10 false *a
*a Pin
*b Guide
*c Lock Pin


Align the 2 pins and 2 guides of the spiral cable with the locations shown in the illustration and attach the 6 claws to install the spiral cable to the steering sensor.

NOTICE:

Do not remove the lock pin before the spiral cable is installed to the steering sensor.



d.

Remove the lock pin from the steering sensor.


Hide 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable sub-assembly with the battery connected and the ignition switch ON.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Check that the front wheels are facing straight ahead.


d.

Attach the claw to install the spiral cable sub-assembly.

NOTICE:

When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.



e.

Connect each connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



f.
B430728C01
1.979,2.948 2.542,2.427 true 1.594,2.896 2.052,3.146 0.458,0.25 10 false *a, *b
*a Slider
*b Lock Position


Connect the airbag connector and check that the slider is in the lock position.

HINT:

If the slider is not in the lock position, the airbag connector is not completely connected. Disconnect the airbag connector, check the airbag connector and spiral cable sub-assembly terminals and connector housings for deformation or foreign matter, and then reconnect the airbag connector.



Hide 45286B 3.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 4.INSTALL LOWER STEERING COLUMN COVER

Hide 5.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.ADJUST SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

Do not adjust the spiral cable sub-assembly with the battery connected and the ignition switch ON.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B404076C01
0.51,2.5 0.927,2.917 0.417,0.417 0.865,2.146 1.281,2.271 true 1.323,2.188 1.635,2.344 0.313,0.156 10 false *a 0.521,2.51 0.719,2.698 0.198,0.188 10 true *b
*a Check Window
*b Matchmark
V100144

U-Turn Point


Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

NOTICE:

When the conditions above cannot be checked via the check window with the front wheels facing straight ahead, there may be a malfunction in the spiral cable sub-assembly. In this case, replace the spiral with cable sensor sub-assembly with a new one.



d.

If the spiral cable sub-assembly is not centered, center it.

i.
B404080C01
0,0 0,0 false
V100145

Interlock
V113147

Counterclockwise


While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.




ii.
B404081C01
0.469,2.49 0.875,2.885 0.406,0.396 0.865,2.156 1.26,2.333 true 1.292,2.26 1.604,2.417 0.313,0.156 10 false *a 0.479,2.5 0.688,2.688 0.208,0.188 10 true *b
*a Check Window
*b Matchmark
V100144

U-Turn Point
V100145

Interlock
V113147

Clockwise


While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly 2.5 times clockwise from the lock position.

HINT:

The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.



iii.

Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

If the cable cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 45100 7.INSTALL STEERING WHEEL ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION