Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM33K0E _56 Audio / Visual / Telematics _043542 NAVIGATION / MULTI INFO DISPLAY _0219471 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the navigation receiver assembly via this circuit.

WIRING DIAGRAM

E317105E06
0.583,1.844 2.229,2.177 1.646,0.333 10 false No. 1 Stereo Jack Adapter Assembly 0.594,1.677 0.927,1.854 0.333,0.177 10 false a1 3.135,1.729 3.958,1.906 0.823,0.177 10 false Radio Wire 5.135,1.833 6.375,2.188 1.24,0.354 10 false Navigation Receiver Assembly 5.115,1.656 5.313,1.833 0.198,0.177 10 false a2 1.573,0.646 2.063,0.823 0.49,0.177 10 false US1+ 2.073,0.552 2.563,0.729 0.49,0.177 10 false 3 1.604,1.198 2.094,1.375 0.49,0.177 10 false US1- 5.24,0.635 5.729,0.813 0.49,0.177 10 false US1+ 5.24,1.219 5.729,1.396 0.49,0.177 10 false US1- 2.063,1.083 2.552,1.26 0.49,0.177 10 false 2 5,1.104 5.49,1.281 0.49,0.177 10 false 2 5.01,0.531 5.5,0.708 0.49,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK RADIO WIRE
a.

Disconnect the a1 No. 1 stereo jack adapter assembly connector.


b.
E317100C09
1.438,0.156 1.844,0.406 0.406,0.25 1.458,1.76 1.865,2.01 0.406,0.25 1.021,0.5 1.583,0.906 true 1.708,0.906 2.281,0.375 true 1.552,2.698 1.135,2.833 true 2.198,2.813 1.74,2.688 true 0.188,0.135 0.406,0.323 0.219,0.188 10 false *a 0.26,1.99 0.479,2.177 0.219,0.188 10 false *b 1.563,0.188 1.76,0.354 0.198,0.167 10 false a1 1.594,1.802 1.792,1.969 0.198,0.167 10 false a2 2.333,0.271 2.75,0.427 0.417,0.156 10 false US1+ 0.802,0.323 1.219,0.479 0.417,0.156 10 false US1- 0.75,2.76 1.167,2.917 0.417,0.156 10 false US1+ 2.271,2.781 2.688,2.938 0.417,0.156 10 false US1-
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the a2 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-3 (US1+) - a2-3 (US1+) Always Below 1 Ω
a1-2 (US1-) - a2-2 (US1-) Always Below 1 Ω
a1-3 (US1+) - Body ground Always 10 kΩ or higher
a1-2 (US1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG