Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM33K0E _59 Vehicle Exterior _043559 DOOR / HATCH _0219590 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Opened Using the Back Door Opener Switch  


DESCRIPTION

The multiplex network door ECU receives an open signal from the back door opener switch assembly via the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B411135E01
0.521,2.354 4.188,2.552 3.667,0.198 10 false : CAN Communication Line 5.188,1.51 6.313,1.875 1.125,0.365 10 false Multiplex Network Door ECU 3.01,1.469 3.469,1.667 0.458,0.198 10 false G16 3.042,1.667 4.552,2.021 1.51,0.354 10 false Certification ECU (Smart Key ECU Assembly) 3.396,1.073 4.01,1.271 0.615,0.198 10 false TSW5 2.177,1.063 2.49,1.26 0.313,0.198 10 false UL 1.458,1.063 1.615,1.26 0.156,0.198 10 false E 1.24,0.833 1.396,1.031 0.156,0.198 10 false 2 2.469,0.823 2.625,1.021 0.156,0.198 10 false 3 3.146,0.823 3.458,1.021 0.313,0.198 10 false 14 1.313,1.302 1.771,1.5 0.458,0.198 10 false V10 1.313,1.469 2.469,1.823 1.156,0.354 10 false Back Door Opener Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

The power back door system troubleshooting procedure is based on the premise that the smart entry and start system (for Entry Function) is operating normally. Check the power back door system first before troubleshooting the power back door system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly (open switch) signal ON or OFF ON: Back door opener switch assembly (open switch) on
OFF: Back door opener switch assembly (open switch) off
-
Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

On GTS screen, item changes between ON and OFF according to above chart.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
2.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


b.

Inspect the back door opener switch assembly

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the V10 back door opener switch assembly connector.


b.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V10-3 (UL) - G16-14 (TSW5) Always Below 1 Ω
V10-2 (E) - Body ground Always Below 1 Ω
V10-3 (UL) or G16-14 (TSW5) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR