Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1GR-FE)
RM33K0E _58 Vehicle Interior _043555 HEATING / AIR CONDITIONING _0219909 COMPRESSOR(for 1GR-FE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
E341235

When replacing the compressor assembly with magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor assembly with magnet clutch before installation.

Standard:

(Oil capacity inside the new compressor assembly with magnet clutch: 150 to 165 cc (5.07 to 5.58 fl.oz)) - (Remaining oil amount in the removed compressor assembly with magnet clutch) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor assembly with magnet clutch is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor assembly with magnet clutch is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 8 or equivalent compressor oil. If any compressor oil other than ND-OIL 8 is used, compressor assembly with magnet clutch insulation performance may decrease, resulting in a leak of electric power.




Hide 2.INSTALL COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH

a.
E341224C01
1.479,0.063 1.729,0.229 0.25,0.167 10 true *1 2.115,0.135 2.365,0.302 0.25,0.167 10 true (1) 3.031,0.271 3.281,0.438 0.25,0.167 10 true (4) 2.896,1.781 3.146,1.948 0.25,0.167 10 true (2) 1.729,1.865 1.979,2.031 0.25,0.167 10 true (3)
*1 Bolt <A>


Temporarily install the compressor assembly with magnet clutch with the generator bracket and 5 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration to install the compressor assembly with magnet clutch.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Install the bolt <A>.

Torque:
Bolt A : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)


d.
E341223

Attach the clamp.


e.

Connect the connector.


Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E341222

Remove the vinyl tape from the suction hose sub-assembly and compressor assembly with magnet clutch.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with magnet clutch.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E341221

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and compressor assembly with magnet clutch.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with magnet clutch.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the No. 1 cooler refrigerant discharge hose to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 53737B 5.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with 6 new clips.


Hide 6.INSTALL FRONT WHEEL LH

Hide 27415 7.INSTALL GENERATOR WITH CLUTCH PULLEY

Hide 16361A 8.INSTALL FAN AND GENERATOR V BELT

Hide 9. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT