Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL INJECTOR
RM33K0E _51 Engine / Hybrid System _043572 1GR-FE FUEL _0220960 FUEL INJECTOR A

1GR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A344533C01
0.333,1.698 0.458,1.969 0.458,1.969 0.604,1.969 false 2.521,0.667 2.76,0.667 2.76,0.667 2.99,1.052 false 0.646,1.885 0.927,2.063 0.281,0.177 10 false *1 2.333,0.594 2.531,0.802 0.198,0.208 10 false *2
*1 O-Ring
*2 Fuel Vibration Insulator


Install a new fuel vibration insulator to each fuel injector assembly.


b.

Apply a light coat of spindle oil or gasoline to new O-rings and install one to each fuel injector assembly.


c.
A344534

Install the 6 fuel injector assemblies.

i.

While turning each fuel injector assembly left and right, install it to the fuel delivery pipe sub-assembly.


ii.

Position the fuel injector assembly connectors so they are facing outward.



Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A344535

Place the fuel delivery pipe sub-assembly together with the 6 fuel injector assemblies on the intake manifold.


b.

Temporarily install the 6 bolts, which are used to hold the fuel delivery pipe sub-assembly to the intake manifold.


c.

Check that the fuel injector assemblies rotate smoothly.

If any fuel injector assembly does not rotate smoothly, replace the O-ring of that fuel injector assembly.


d.

Position the fuel injector assemblies so that the connectors are facing outward.


e.

Tighten the 6 bolts, which are used to hold the fuel delivery pipe sub-assembly to the intake manifold.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


f.

Connect the 6 fuel injector assembly connectors to the 6 fuel injector assemblies.


Hide 23802B 3.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

a.

Connect the No. 2 fuel pipe sub-assembly and install the No. 2 fuel pipe clamp to the fuel pressure regulator assembly.

Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 23801P 4.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

Connect the No. 1 fuel pipe sub-assembly and install the No. 2 fuel pipe clamp to the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 17129 5.INSTALL INTAKE AIR SURGE TANK

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 7.INSPECT FOR FUEL LEAK

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed / ON.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5

iv.

Check that there are no leaks from the fuel system.

If there are fuel leaks, repair or replace parts as necessary.


v.

Turn the ignition switch off.


vi.

Disconnect the GTS from the DLC3.