Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST PIPE
RM33K0E _51 Engine / Hybrid System _043578 1GR-FE INTAKE / EXHAUST _0220972 EXHAUST PIPE A

1GR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install the front exhaust pipe assembly to the No. 1 exhaust pipe support.


b.

Install a new gasket.

NOTICE:

Do not reuse the gaskets.



c.

Connect the front exhaust pipe assembly to the exhaust manifold sub-assembly RH with the 2 new nuts.

Torque:
54.3 N*m (554 kgf*cm, 40 ft.*lbf)


Hide 89465 2.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 89465 3.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17450B 4.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.

Install the front No. 2 exhaust pipe assembly to the No. 1 exhaust pipe support.


b.

Install 2 new gaskets.

NOTICE:

Do not reuse the gaskets.



c.

Connect the front No. 2 exhaust pipe assembly to the exhaust manifold sub-assembly LH with the 2 new nuts.

Torque:
54.3 N*m (554 kgf*cm, 40 ft.*lbf)


d.

Connect the front No. 2 exhaust pipe assembly to the front exhaust pipe assembly with the 2 bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.
A356049

Connect the heated oxygen sensor connector.


f.

Attach the 2 clamps.


Hide 17420 5.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.
A111834

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

40 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.
A076194C38
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.271,1.781 1.49,1.958 0.219,0.177 10 false *1 3.104,0.875 3.323,1.052 0.219,0.177 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with front exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the tail exhaust pipe assembly, do not push in the gasket with the tail exhaust pipe assembly.




d.

Install the center exhaust pipe assembly to the 3 No. 1 exhaust pipe supports.


e.

Install a new gasket and the center exhaust pipe assembly to the front exhaust pipe assembly with the 2 compressionspring and 2 bolts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 6.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install the tail exhaust pipe assembly to the No. 2 exhaust pipe support.


b.

Install a new gasket and the tail exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts and 2 new nuts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

Do not reuse the gasket.