Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM33K0E _51 Engine / Hybrid System _043565 1GR-FE ENGINE CONTROL _0222009 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly (No. 4 cylinder) circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil assembly (No. 5 cylinder) circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil assembly (No. 6 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF1) signal to the ECM, for each cylinder ignition.

A319209E01
5.417,1.292 5.583,0.708 5.583,0.708 5.75,0.708 false 4.688,1.667 4.833,0.917 4.833,0.917 4.667,0.917 false 0.344,2.042 2.167,2.313 1.823,0.271 10 false Crankshaft Position Sensor 0.385,4.115 2.208,4.385 1.823,0.271 10 false VVT Sensor 0.229,5.76 2.125,6.542 1.896,0.781 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.198,1.531 3.625,1.781 0.427,0.25 10 false IGT1 3.188,1.99 3.615,2.24 0.427,0.25 10 false IGF1 3.198,2.927 3.625,3.177 0.427,0.25 10 false IGT2 3.208,4.01 3.635,4.26 0.427,0.25 10 false IGT3 3.198,5.073 3.625,5.323 0.427,0.25 10 false IGT4 3.198,6.156 3.625,6.406 0.427,0.25 10 false IGT5 3.198,7.24 3.625,7.49 0.427,0.25 10 false IGT6 4.771,0.396 6.01,0.615 1.24,0.219 10 false from Battery 4.229,0.833 5.469,1.052 1.24,0.219 10 false Igniter 5.844,0.646 6.938,1.219 1.094,0.573 10 false No. 1 Ignition Coil Assembly 5.833,1.51 7.073,1.729 1.24,0.219 10 false No. 1 Cylinder 5.885,2.115 6.844,2.344 0.958,0.229 10 false Spark Plug 4.427,2.844 5.521,3.417 1.094,0.573 10 false No. 2 Ignition Coil Assembly 4.438,3.938 5.531,4.51 1.094,0.573 10 false No. 3 Ignition Coil Assembly 4.427,5.01 5.521,5.583 1.094,0.573 10 false No. 4 Ignition Coil Assembly 4.427,6.094 5.521,6.667 1.094,0.573 10 false No. 5 Ignition Coil Assembly 4.406,7.177 5.5,7.75 1.094,0.573 10 false No. 6 Ignition Coil Assembly 5.781,3.302 7.021,3.521 1.24,0.219 10 false No. 2 Cylinder 5.813,4.406 7.052,4.625 1.24,0.219 10 false No. 3 Cylinder 5.802,5.469 7.042,5.688 1.24,0.219 10 false No. 4 Cylinder 5.854,6.563 7.094,6.781 1.24,0.219 10 false No. 5 Cylinder 5.833,7.635 7.073,7.854 1.24,0.219 10 false No. 6 Cylinder 3.021,8.021 3.448,8.271 0.427,0.25 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

INJ relay

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

INJ relay

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

INJ relay

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

INJ relay

·

ECM


Comes on DTC stored
P0355 Ignition Coil "E" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT5 circuit between ignition coil assembly and ECM

·

No. 5 ignition coil assembly

·

INJ relay

·

ECM


Comes on DTC stored
P0356 Ignition Coil "F" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT6 circuit between ignition coil assembly and ECM

·

No. 6 ignition coil assembly

·

INJ relay

·

ECM


Comes on DTC stored

A210049E13
2.875,1.667 3.208,1.813 0.333,0.146 10 false GND 2.875,2.542 3.208,2.698 0.333,0.156 10 false GND 1.177,2.646 1.927,2.833 0.75,0.188 10 false 20 ms./DIV. 2.5,0.521 3.042,0.656 0.542,0.135 10 false 2 V/DIV. 0.156,1.156 0.427,1.365 0.271,0.208 10 false IGT 0.156,2.01 0.635,2.208 0.479,0.198 10 false IGF1

Reference: Inspection using an oscilloscope

HINT:

While idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.


ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

A212405E36
1.781,1.646 2.177,1.823 0.396,0.177 10 false ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 false IGT 2.948,1.729 3.698,2.198 0.75,0.469 10 false IGF1 4.156,1.51 4.594,1.656 0.438,0.146 10 false Igniter 5.396,1.344 6.167,1.521 0.771,0.177 10 false Ignition Coil 4.469,2.354 5.875,2.542 1.406,0.188 10 false Ignition Coil Assembly 0.208,3.115 1.146,3.448 0.938,0.333 10 false Ignition Signal (IGT) 1.646,3.542 2.135,3.729 0.49,0.188 10 false Normal 1.385,3.948 2.156,4.135 0.771,0.188 10 false Malfunction 0.188,3.896 1.156,4.417 0.969,0.521 10 false Ignition Confirmation Signal (IGF1) 3.635,4.51 4.49,4.688 0.854,0.177 10 false Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter (Cylinder 1 to 6)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353, P0354, P0355 or P0356.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A372120E01
1.198,0.625 1.615,0.792 0.417,0.167 10 false J/B-B 2.646,0.615 3.396,0.781 0.75,0.167 10 false AM2 NO.2 4.333,0.333 4.5,0.5 0.167,0.167 10 false 5 5.167,0.333 5.333,0.5 0.167,0.167 10 false 3 4.333,0.75 4.5,0.917 0.167,0.167 10 false 1 5.167,0.75 5.333,0.917 0.167,0.167 10 false 2 4.667,1.167 5,1.333 0.333,0.167 10 false IG2 0.917,1.083 1.167,1.25 0.25,0.167 10 false 20 0.75,1.333 1.167,1.5 0.417,0.167 10 false IG1D 1.25,1.417 1.583,1.583 0.333,0.167 10 false G16 1.25,1.583 4.083,1.833 2.833,0.25 10 false Certification ECU (Smart Key ECU Assembly) 0.5,3.281 1.5,3.531 1,0.25 10 false FL MAIN 3.0W 0.583,3.917 1.083,4.167 0.5,0.25 10 false Battery 3.646,3.083 3.896,3.25 0.25,0.167 10 false INJ 1.479,4.5 1.646,4.667 0.167,0.167 10 false A 3.333,3.667 3.5,3.833 0.167,0.167 10 false 3 4.115,3.667 4.281,3.833 0.167,0.167 10 false 5 3.333,4.063 3.5,4.229 0.167,0.167 10 false 1 4.125,4.073 4.292,4.24 0.167,0.167 10 false 2 3.667,4.5 3.917,4.667 0.25,0.167 10 false INJ 5.021,4.354 5.688,4.521 0.667,0.167 10 false IG2 NO.1 5.125,4.01 5.292,4.177 0.167,0.167 10 false 2 5.365,4.01 5.531,4.177 0.167,0.167 10 false 1

A372121E01
3.167,0.583 3.333,0.75 0.167,0.167 10 false 1 1.479,0.271 1.646,0.469 0.167,0.198 10 false A 3.167,1.083 3.333,1.25 0.167,0.167 10 false 4 3.385,0.729 3.667,0.927 0.281,0.198 10 false +B 3.385,1.177 3.75,1.375 0.365,0.198 10 false GND 3.917,0.729 4.25,0.927 0.333,0.198 10 false IGT1 4,1.167 4.281,1.365 0.281,0.198 10 false IGF 4.385,0.583 4.5,0.75 0.115,0.167 10 false 3 4.385,1.052 4.583,1.25 0.198,0.198 10 false 2 2.917,1.333 3.25,1.5 0.333,0.167 10 false C27 2.917,1.5 4.75,1.75 1.833,0.25 10 false No. 1 Ignition Coil Assembly 5.615,0.5 5.865,0.667 0.25,0.167 10 false 27 5.542,2.052 5.906,2.25 0.365,0.198 10 false C118 6,0.552 6.365,0.75 0.365,0.198 10 false IGT1 5.531,1.177 5.896,1.375 0.365,0.198 10 false C119 5.615,0.969 5.865,1.135 0.25,0.167 10 false 23 6,1.052 6.365,1.25 0.365,0.198 10 false IGF1 3.917,2.031 4.281,2.198 0.365,0.167 10 false IGT2 2.917,2.583 3.198,2.75 0.281,0.167 10 false C28 2.917,3.833 3.198,4 0.281,0.167 10 false C29 3.969,3.302 4.333,3.469 0.365,0.167 10 false IGT3 2.917,5.083 3.25,5.25 0.333,0.167 10 false C30 3.969,4.563 4.333,4.729 0.365,0.167 10 false IGT4 3.969,5.813 4.333,5.979 0.365,0.167 10 false IGT5 2.917,6.333 3.531,6.531 0.615,0.198 10 false C126 3.969,7.073 4.333,7.24 0.365,0.167 10 false IGT6 2.917,7.583 3.531,7.781 0.615,0.198 10 false C127 5.615,1.833 5.813,2 0.198,0.167 10 false 28 6,1.917 6.333,2.083 0.333,0.167 10 false IGT2 5.604,3.083 5.802,3.25 0.198,0.167 10 false 25 6,3.167 6.333,3.333 0.333,0.167 10 false IGT3 6,4.417 6.333,4.583 0.333,0.167 10 false IGT4 6,5.667 6.333,5.833 0.333,0.167 10 false IGT5 6,6.917 6.333,7.083 0.333,0.167 10 false IGT6 5.615,6.833 5.865,7 0.25,0.167 10 false 28 5.615,5.583 5.865,5.75 0.25,0.167 10 false 27 5.604,4.333 5.854,4.5 0.25,0.167 10 false 26 6.333,7.833 6.75,8 0.417,0.167 10 false ECM 3.167,1.917 3.333,2.083 0.167,0.167 10 false 1 3.167,3.25 3.333,3.417 0.167,0.167 10 false 1 3.167,4.417 3.333,4.583 0.167,0.167 10 false 1 3.167,5.667 3.333,5.833 0.167,0.167 10 false 1 3.167,6.917 3.333,7.083 0.167,0.167 10 false 1 3.167,2.333 3.333,2.5 0.167,0.167 10 false 4 3.167,3.583 3.333,3.75 0.167,0.167 10 false 4 3.167,4.833 3.333,5 0.167,0.167 10 false 4 3.167,6.083 3.333,6.25 0.167,0.167 10 false 4 3.167,7.333 3.333,7.5 0.167,0.167 10 false 4 4.385,1.917 4.5,2.083 0.115,0.167 10 false 3 4.385,3.167 4.5,3.333 0.115,0.167 10 false 3 4.417,4.417 4.531,4.583 0.115,0.167 10 false 3 4.417,5.667 4.531,5.833 0.115,0.167 10 false 3 4.417,6.917 4.531,7.083 0.115,0.167 10 false 3 4.385,2.302 4.583,2.5 0.198,0.198 10 false 2 4.385,3.552 4.583,3.75 0.198,0.198 10 false 2 4.417,4.833 4.615,5.031 0.198,0.198 10 false 2 4.417,6.083 4.615,6.281 0.198,0.198 10 false 2 4.417,7.302 4.615,7.5 0.198,0.198 10 false 2 3.417,2.021 3.698,2.219 0.281,0.198 10 false +B 3.385,3.302 3.667,3.5 0.281,0.198 10 false +B 3.385,4.552 3.667,4.75 0.281,0.198 10 false +B 3.417,5.802 3.698,6 0.281,0.198 10 false +B 3.417,7.063 3.698,7.26 0.281,0.198 10 false +B 3.417,2.427 3.781,2.625 0.365,0.198 10 false GND 3.385,4.938 3.75,5.135 0.365,0.198 10 false GND 3.417,6.198 3.781,6.396 0.365,0.198 10 false GND 3.385,3.667 3.75,3.865 0.365,0.198 10 false GND 3.385,7.448 3.75,7.646 0.365,0.198 10 false GND 4,2.417 4.281,2.615 0.281,0.198 10 false IGF 3.969,3.656 4.25,3.854 0.281,0.198 10 false IGF 4,4.917 4.281,5.115 0.281,0.198 10 false IGF 4,6.188 4.281,6.385 0.281,0.198 10 false IGF 4,7.448 4.281,7.646 0.281,0.198 10 false IGF 2.917,2.75 4.75,3 1.833,0.25 10 false No. 2 Ignition Coil Assembly 2.917,4 4.75,4.25 1.833,0.25 10 false No. 3 Ignition Coil Assembly 2.917,5.25 4.75,5.5 1.833,0.25 10 false No. 4 Ignition Coil Assembly 2.917,6.5 4.75,6.75 1.833,0.25 10 false No. 5 Ignition Coil Assembly 2.917,7.75 4.75,8 1.833,0.25 10 false No. 6 Ignition Coil Assembly 5.542,0.74 5.906,0.938 0.365,0.198 10 false C118 5.542,3.313 5.906,3.51 0.365,0.198 10 false C119 5.531,4.563 5.896,4.76 0.365,0.198 10 false C119 5.542,5.813 5.906,6.01 0.365,0.198 10 false C119 5.542,7.073 5.906,7.271 0.365,0.198 10 false C119

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTCS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not change the location of the connectors.



g.

Perform a simulation test.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A115969C11
1.26,1.417 1.667,1.667 0.406,0.25 1.75,1.417 2.156,1.667 0.406,0.25 1.26,1.083 1.667,1.333 0.406,0.25 1.26,0.75 1.667,1 0.406,0.25 1.75,1.083 2.156,1.333 0.406,0.25 1.75,0.75 2.156,1 0.406,0.25 1.354,2.302 0.833,2.813 true 2.115,2.292 2.583,2.813 true 0.167,0.094 0.458,0.354 0.292,0.26 10 false *a 0.656,2.833 1.26,3.094 0.604,0.26 10 false +B 1.354,0.802 1.667,1 0.313,0.198 10 false C27 2.604,2.813 3.208,3.073 0.604,0.26 10 false GND 1.854,0.802 2.167,1 0.313,0.198 10 false C28 1.354,1.135 1.667,1.333 0.313,0.198 10 false C29 1.854,1.135 2.167,1.333 0.313,0.198 10 false C30 1.313,1.469 1.729,1.635 0.417,0.167 10 false C126 1.802,1.469 2.219,1.635 0.417,0.167 10 false C127
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C27-1 (+B) - C27-4 (GND) Engine switch on (IG) 11 to 14 V
C28-1 (+B) - C28-4 (GND) Engine switch on (IG) 11 to 14 V
C29-1 (+B) - C29-4 (GND) Engine switch on (IG) 11 to 14 V
C30-1 (+B) - C30-4 (GND) Engine switch on (IG) 11 to 14 V
C126-1 (+B) - C126-4 (GND) Engine switch on (IG) 11 to 14 V
C127-1 (+B) - C127-4 (GND) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-3 (IGT1) - C118-27 (IGT1) Always Below 1 Ω
C28-3 (IGT2) - C118-28 (IGT2) Always Below 1 Ω
C29-3 (IGT3) - C119-25 (IGT3) Always Below 1 Ω
C30-3 (IGT4) - C119-26 (IGT4) Always Below 1 Ω
C126-3 (IGT5) - C119-27 (IGT5) Always Below 1 Ω
C127-3 (IGT6) - C119-28 (IGT6) Always Below 1 Ω
C27-2 (IGF) - C119-23 (IGF1) Always Below 1 Ω
C28-2 (IGF) - C119-23 (IGF1) Always Below 1 Ω
C29-2 (IGF) - C119-23 (IGF1) Always Below 1 Ω
C30-2 (IGF) - C119-23 (IGF1) Always Below 1 Ω
C126-2 (IGF) - C119-23 (IGF1) Always Below 1 Ω
C127-2 (IGF) - C119-23 (IGF1) Always Below 1 Ω
C27-3 (IGT1) or C118-27 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C28-3 (IGT2) or C118-28 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C29-3 (IGT3) or C119-25 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C30-3 (IGT4) or C119-26 (IGT4) - Body ground and other terminals Always 10 kΩ or higher
C126-3 (IGT5) or C119-27 (IGT5) - Body ground and other terminals Always 10 kΩ or higher
C127-3 (IGT6) or C119-28 (IGT6) - Body ground and other terminals Always 10 kΩ or higher
C27-2 (IGF) or C119-23 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C28-2 (IGF) or C119-23 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C29-2 (IGF) or C119-23 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C30-2 (IGF) or C119-23 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C126-2 (IGF) or C119-23 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C127-2 (IGF) or C119-23 (IGF1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-4 (GND) - Body ground Always Below 1 Ω
C28-4 (GND) - Body ground Always Below 1 Ω
C29-4 (GND) - Body ground Always Below 1 Ω
C30-4 (GND) - Body ground Always Below 1 Ω
C126-4 (GND) - Body ground Always Below 1 Ω
C127-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INJ RELAY - IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INJ RELAY - IGNITION COIL ASSEMBLY)
a.

Remove the INJ relay from the engine room relay block and junction block assembly.


b.

Disconnect the ignition coil assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INJ relay terminal 3 - C27-1 (+B) Always Below 1 Ω
INJ relay terminal 3 - C28-1 (+B) Always Below 1 Ω
INJ relay terminal 3 - C29-1 (+B) Always Below 1 Ω
INJ relay terminal 3 - C30-1 (+B) Always Below 1 Ω
INJ relay terminal 3 - C126-1 (+B) Always Below 1 Ω
INJ relay terminal 3 - C127-1 (+B) Always Below 1 Ω
INJ relay terminal 3 or C27-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
INJ relay terminal 3 or C28-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
INJ relay terminal 3 or C29-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
INJ relay terminal 3 or C30-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
INJ relay terminal 3 or C126-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
INJ relay terminal 3 or C127-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INJ RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INJ RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJ RELAY)

NG

REPLACE INJ RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJ RELAY)
A349020C02
0.188,0.156 0.5,0.354 0.313,0.198 10 false *1 0.948,2.958 1.26,3.156 0.313,0.198 10 false *2
*1 Engine Room Relay Block Assembly
*2 INJ Relay


a.

Remove the INJ relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
INJ relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (INJ RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJ RELAY - BATTERY)

8.CHECK HARNESS AND CONNECTOR (INJ RELAY - BODY GROUND)
a.

Remove the INJ relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INJ relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (INJ RELAY - IG2 NO.1 FUSE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (INJ RELAY - IG2 NO.1 FUSE)
a.

Remove the INJ relay from the engine room relay block and junction block assembly.


b.

Remove the IG2 NO.1 fuse from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INJ relay terminal 2 - IG2 NO.1 fuse terminal 2 Always Below 1 Ω
INJ relay terminal 2 or IG2 NO.1 fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR