Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM33K0E _51 Engine / Hybrid System _043565 1GR-FE ENGINE CONTROL _0222009 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E27
1.625,0.823 2.938,1.115 1.313,0.292 10 false from EFI-B Fuse 0.99,1.177 2.74,1.427 1.75,0.25 10 false from EFI-MAIN NO.1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.573,3.083 2.438,0.438 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

VC Power Source Circuit
A348214E02
0.5,0.667 0.958,0.865 0.458,0.198 10 false C129 0.5,0.833 2,1.25 1.5,0.417 10 false VVT Sensor (for Intake Camshaft of Bank 1) 0.5,2.083 0.958,2.281 0.458,0.198 10 false C128 0.5,3.5 0.958,3.698 0.458,0.198 10 false C13 0.5,5.417 0.958,5.615 0.458,0.198 10 false A30 0.5,0.833 2,1.25 1.5,0.417 10 false VVT Sensor (for Intake Camshaft of Bank 1) 0.5,2.25 2,2.667 1.5,0.417 10 false VVT Sensor (for Intake Camshaft of Bank 2) 0.5,3.667 1.667,4.083 1.167,0.417 10 false Throttle Body with Motor Assembly 0.5,5.583 1.667,6 1.167,0.417 10 false Accelerator Pedal Sensor Assembly 2.083,0.719 2.698,0.917 0.615,0.198 10 false VVR+ 2.083,1.167 2.698,1.365 0.615,0.198 10 false VVR- 2.083,2.135 2.698,2.333 0.615,0.198 10 false VVL+ 2.083,2.583 2.698,2.781 0.615,0.198 10 false VVL- 2.25,3.583 2.698,3.833 0.448,0.25 10 false E2 2.083,4.052 2.698,4.25 0.615,0.198 10 false VTA2 2.25,4.5 2.583,4.75 0.333,0.25 10 false VC 2.167,4.917 2.698,5.167 0.531,0.25 10 false VTA 2.083,5.469 2.698,5.667 0.615,0.198 10 false VCP2 2.083,5.885 2.698,6.083 0.615,0.198 10 false EPA2 2.083,6.333 2.698,6.531 0.615,0.198 10 false VPA2 2.083,6.802 2.698,7 0.615,0.198 10 false VCPA 2.167,7.219 2.698,7.417 0.531,0.198 10 false EPA 2.167,7.667 2.698,7.917 0.531,0.25 10 false VPA 2.25,3.052 2.865,3.25 0.615,0.198 10 false VC 2.25,1.635 2.865,1.833 0.615,0.198 10 false VC 5.333,5.333 5.948,5.531 0.615,0.198 10 false VCP2 5.333,5.802 5.948,6 0.615,0.198 10 false EPA2 5.333,6.333 5.948,6.531 0.615,0.198 10 false VPA2 5.333,6.667 5.948,6.865 0.615,0.198 10 false VCPA 5.333,7.135 5.865,7.333 0.531,0.198 10 false EPA 5.333,7.667 5.865,7.917 0.531,0.25 10 false VPA 5.333,7.667 5.865,7.917 0.531,0.25 10 false VPA 5.802,8.25 6.167,8.5 0.365,0.25 10 false ECM 6.365,0.729 6.698,0.979 0.333,0.25 10 false 5 V 5.333,3.469 5.948,3.667 0.615,0.198 10 false ETA 5.333,4.052 5.948,4.25 0.615,0.198 10 false VTA2 5.333,4.917 5.865,5.167 0.531,0.25 10 false VTA1 5.333,4.385 5.948,4.583 0.615,0.198 10 false VCTA 5.333,1.5 5.948,1.698 0.615,0.198 10 false VCV1 5.333,2.917 5.948,3.115 0.615,0.198 10 false VCV2 5.333,0.719 5.948,0.917 0.615,0.198 10 false VV1+ 5.333,1.052 5.948,1.25 0.615,0.198 10 false VV1- 5.333,2.469 5.948,2.667 0.615,0.198 10 false VV2- 5.333,2.167 5.948,2.365 0.615,0.198 10 false VV2+ 4.927,0.74 5.385,0.938 0.458,0.198 10 false C120 4.917,3.615 5.375,3.813 0.458,0.198 10 false C118 4.917,5.458 5.375,5.656 0.458,0.198 10 false G159 4.917,7.25 5.375,7.448 0.458,0.198 10 false G158 2.583,2.021 2.74,2.219 0.156,0.198 10 false 1 4.99,0.5 5.302,0.698 0.313,0.198 10 false 10 5,0.958 5.313,1.156 0.313,0.198 10 false 11 5.01,1.417 5.323,1.615 0.313,0.198 10 false 12 2.583,1.063 2.74,1.26 0.156,0.198 10 false 2 2.583,1.51 2.74,1.708 0.156,0.198 10 false 3 2.583,0.615 2.74,0.813 0.156,0.198 10 false 1 2.594,2.469 2.75,2.667 0.156,0.198 10 false 2 2.594,2.917 2.75,3.115 0.156,0.198 10 false 3 5.031,1.917 5.188,2.115 0.156,0.198 10 false 4 5.031,2.375 5.188,2.573 0.156,0.198 10 false 5 5.042,2.823 5.198,3.021 0.156,0.198 10 false 6 2.583,3.49 2.74,3.688 0.156,0.198 10 false 3 2.583,3.927 2.74,4.125 0.156,0.198 10 false 4 2.583,4.375 2.74,4.573 0.156,0.198 10 false 5 2.594,4.833 2.75,5.031 0.156,0.198 10 false 6 5.042,3.385 5.198,3.583 0.156,0.198 10 false 3 5.042,3.844 5.198,4.042 0.156,0.198 10 false 9 5.042,4.292 5.198,4.49 0.156,0.198 10 false 2 5.031,4.74 5.188,4.938 0.156,0.198 10 false 1 2.583,5.771 2.74,5.969 0.156,0.198 10 false 2 2.573,5.323 2.729,5.521 0.156,0.198 10 false 1 2.583,6.229 2.74,6.427 0.156,0.198 10 false 3 2.594,6.677 2.75,6.875 0.156,0.198 10 false 4 2.594,7.125 2.75,7.323 0.156,0.198 10 false 5 2.594,7.573 2.75,7.771 0.156,0.198 10 false 6 5.042,5.229 5.198,5.427 0.156,0.198 10 false 3 5.042,5.688 5.198,5.885 0.156,0.198 10 false 4 5.042,6.125 5.198,6.323 0.156,0.198 10 false 5 5.042,6.583 5.198,6.781 0.156,0.198 10 false 6 5.042,7.031 5.198,7.229 0.156,0.198 10 false 1 5.042,7.469 5.198,7.667 0.156,0.198 10 false 2 4.927,1.188 5.385,1.385 0.458,0.198 10 false C120 4.917,1.635 5.375,1.833 0.458,0.198 10 false C120 4.927,2.156 5.385,2.354 0.458,0.198 10 false C120 4.927,2.604 5.385,2.802 0.458,0.198 10 false C120 4.927,3.052 5.385,3.25 0.458,0.198 10 false C120 4.927,4.063 5.385,4.26 0.458,0.198 10 false C118 4.917,4.51 5.375,4.708 0.458,0.198 10 false C118 4.917,4.958 5.375,5.156 0.458,0.198 10 false C118 4.917,5.906 5.375,6.104 0.458,0.198 10 false G159 4.917,6.354 5.375,6.552 0.458,0.198 10 false G159 4.917,6.802 5.375,7 0.458,0.198 10 false G159 4.927,7.698 5.385,7.896 0.458,0.198 10 false G158

For the circuit diagram of the ECM power source circuit.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit

CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A266666C02
0.417,1.083 0.833,1.333 0.417,0.25 0.417,2.583 0.625,1.938 true 1,2.583 0.708,1.938 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.458,1.135 0.917,1.333 0.458,0.198 10 false G158 0.333,2.667 0.906,2.917 0.573,0.25 10 false 23 (+B) 1,2.667 1.583,2.917 0.583,0.25 10 false 22 (+B2)
*a Rear view of wire harness connector (to ECM)


Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G158-23 (+B) - Body ground Engine switch on (IG) 11 to 14 V
G158-22 (+B2) - Body ground Engine switch on (IG) 11 to 14 V


HINT:

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.



Result:
Proceed to
OK
NG



OK

3.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY (CHECK FOR SHORT IN THROTTLE POSITION SENSOR)

NG

3.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY (CHECK FOR SHORT IN THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



A

4.CHECK ACCELERATOR PEDAL SENSOR ASSEMBLY (CHECK FOR SHORT IN ACCELERATOR PEDAL SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK ACCELERATOR PEDAL SENSOR ASSEMBLY (CHECK FOR SHORT IN ACCELERATOR PEDAL SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK VVT SENSOR (CHECK FOR SHORT IN VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK VVT SENSOR (CHECK FOR SHORT IN VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK VVT SENSOR (CHECK FOR SHORT IN VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1)

6.CHECK VVT SENSOR (CHECK FOR SHORT IN VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2)

7.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


d.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C118-2 (VCTA) - Body ground and other terminals Always 10 kΩ or higher
G159-6 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
G159-3 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
C120-12 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C120-6 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR