Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM33K0E _51 Engine / Hybrid System _043565 1GR-FE ENGINE CONTROL _0222009 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch and to terminal STA of the ECM (STA signal).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

12.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS.

OK:
Condition Starter Signal
Engine switch on (IG) OFF
Engine cranking ON



Result:
Proceed to
OK
NG



OK

3.INSPECT RELAY (ST NO. 1 RELAY)

NG

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT RELAY (ST NO. 1 RELAY)

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE RELAY (ST NO. 1)

4.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>1GR-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from the engine room relay block.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 3 - C26-1 Always Below 1 Ω
ST NO. 1 relay terminal 3 or C26-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Battery cable positive (+) terminal - D3-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-5 (L) - ST NO. 1 relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - C22-4 (B) Always Below 1 Ω
G17-16 (STAR) - C120-23 (NSW) Always Below 1 Ω
G17-16 (STAR) or C22-4 (B) - Body ground and other terminals Always 10 kΩ or higher
G17-16 (STAR) or C120-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ST NO. 1 RELAY, CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ST NO. 1 RELAY, CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-28 (STA) - C22-5 (L) Always Below 1 Ω
G159-28 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
G159-28 (STA) - G17-37 (STA) Always Below 1 Ω
G159-28 (STA) or C22-5 (L) - Body ground and other terminals Always 10 kΩ or higher
G159-28 (STA) or ST NO. 1 relay terminal 2 - Body ground and other terminals Always 10 kΩ or higher
G159-28 (STA) or G17-37 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS.

OK:
Condition Starter Signal
Engine switch on (IG) OFF
Engine cranking ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)