Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM33K0E _51 Engine / Hybrid System _043565 1GR-FE ENGINE CONTROL _0222009 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG)
(b) STP signal off when ST1- signal off
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A372124E01
1.188,0.417 1.604,0.583 0.417,0.167 10 false J/B-B 2.667,0.417 3.417,0.583 0.75,0.167 10 false AM2 NO.2 4.333,0.083 4.5,0.25 0.167,0.167 10 false 5 5.167,0.083 5.333,0.25 0.167,0.167 10 false 3 5.167,0.5 5.333,0.667 0.167,0.167 10 false 2 4.333,0.5 4.5,0.667 0.167,0.167 10 false 1 4.667,1 5,1.167 0.333,0.167 10 false IG2 0.917,0.917 1.167,1.083 0.25,0.167 10 false 20 1.25,1.167 1.583,1.333 0.333,0.167 10 false G16 1.25,1.333 4.083,1.583 2.833,0.25 10 false Certification ECU (Smart Key ECU Assembly) 0.708,1.167 1.125,1.333 0.417,0.167 10 false IG1D 0.5,3.333 1.5,3.5 1,0.167 10 false FL MAIN 3.0W 0.583,4 1.083,4.25 0.5,0.25 10 false Battery 3.5,3.583 3.833,3.75 0.333,0.167 10 false ALT 3.875,3.917 4.292,4.083 0.417,0.167 10 false STOP 4.5,3.167 4.667,3.333 0.167,0.167 10 false 6 4.667,2.75 5.333,2.917 0.667,0.167 10 false IG2 NO.3 5.083,2.417 5.25,2.583 0.167,0.167 10 false 1 4.75,2.417 4.917,2.583 0.167,0.167 10 false 2 5.417,3.167 5.583,3.333 0.167,0.167 10 false 5 4.5,4 4.667,4.167 0.167,0.167 10 false 7 4.75,3.333 4.917,3.5 0.167,0.167 10 false B 5.083,3.333 5.25,3.5 0.167,0.167 10 false L 5.417,4 5.583,4.167 0.167,0.167 10 false 3 4.75,4.125 4.917,4.292 0.167,0.167 10 false B 5.083,4.125 5.25,4.292 0.167,0.167 10 false L 4.75,4.531 5.083,4.698 0.333,0.167 10 false GND 4.5,4.417 4.667,4.583 0.167,0.167 10 false 2 4.167,5 4.5,5.167 0.333,0.167 10 false A64 4.167,5.167 5.917,5.417 1.75,0.25 10 false Stop Light Switch Assembly 6.25,4.917 6.667,5.083 0.417,0.167 10 false G159 6.25,5.083 6.667,5.25 0.417,0.167 10 false ECM 5.75,4 6,4.167 0.25,0.167 10 false 35 5.75,3.167 6,3.333 0.25,0.167 10 false 34 6.083,3.167 6.5,3.333 0.417,0.167 10 false ST1- 6.083,4 6.5,4.167 0.417,0.167 10 false STP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
E270270C13
0.167,1 0.583,1.25 0.417,0.25 2.375,1.188 2.792,1.854 true 0.25,1.052 0.708,1.25 0.458,0.198 10 false A64 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.781,1.896 2.938,2.094 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
E270270C14
0.167,1 0.583,1.25 0.417,0.25 2.042,1.208 1.479,1.823 true 0.25,1.052 0.708,1.25 0.458,0.198 10 false A64 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.406,1.865 1.563,2.063 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A64-6 (B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (IG2 NO.3 FUSE - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.

A353946C03
4.583,1.76 5,2 0.417,0.24 5.094,2.521 5.51,2.198 true 6,2.552 5.583,2.198 true 1.156,2.021 1.469,2.177 0.313,0.156 10 false *a 2.854,2 3.167,2.156 0.313,0.156 10 false *b 3.917,0.083 4.229,0.24 0.313,0.156 10 false *c 4.625,1.802 5,2 0.375,0.198 10 false G159 4.802,2.469 5.26,2.667 0.458,0.198 10 false STP 6.052,2.49 6.51,2.688 0.458,0.198 10 false ST1-
*a Brake Pedal Depressed *b Brake Pedal Released
*c Rear view of wire harness connector
(to ECM)
- -



b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G159-34 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
G159-35 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (L) - G159-35 (STP) Always Below 1 Ω
A64-5 (L) - G159-34 (ST1-) Always Below 1 Ω
A64-3 (L) or G159-35 (STP) - Body ground Always 10 kΩ or higher
A64-5 (L) or G159-34 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IG2 NO.3 FUSE - STOP LIGHT SWITCH ASSEMBLY)
a.

Remove the IG2 NO.3 fuse from the instrument panel junction block assembly.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 NO.3 fuse terminal 2 - A64-6 Always Below 1 Ω
IG2 NO.3 fuse terminal 2 or A64-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR