When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Make sure foreign matter does not enter the fuel path.
22100
1.INSTALL SUPPLY PUMP ASSEMBLY
| *a | w/ DPF or Pressurized Fuel Filter |
| *b | w/o DPF or Pressurized Fuel Filter |
Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.
With SST set, do not turn the crankshaft more than a half rotation.
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the supply pump assembly.
| *a | Groove |
To insert the supply pump assembly shaft in the supply pump shaft sprocket, it may be necessary to turn the supply pump assembly several degrees and the groove in the supply pump assembly shaft are aligned.
| *a | Supply Pump Shaft Key |
| *b | Upper Side |
When installing a new supply pump assembly, adjust the supply pump assembly injection pump drive shaft key assignment by turning the supply pump assembly shown in the illustration.
| *a | Hold |
|
Turn |
Using SST, tighten clockwise direction the supply pump assembly, and then temporarily install the 3 fuel supply pump fixing nuts.
Using SST, tighten and insert the supply pump assembly up to the position shown in the illustration and tighten the 3 fuel supply pump fixing nuts.
After tightening the part with SST, a gap of 2 to 3 mm in area A shown in the illustration is normal.
w/ DPF or Pressurized Fuel Filter:
Install the No. 1 fuel pump bracket with the 2 bolts to the supply pump assembly and cylinder block sub-assembly.
Remove SST and the 3 set bolts.
| *a | Hold |
|
Turn |
Using SST, hold the crankshaft pulley sub-assembly and tighten the set nut.
11324
2.INSTALL TIMING CHAIN COVER PLATE
Install the timing chain cover plate and new gasket with the 3 bolts.
Do not install the timing chain cover plate with the bolts included with SST.
3.INSTALL FUEL PUMP MOTOR WIRE
Attach the clamp and install the fuel pump motor wire.
Connect the fuel pump motor wire connector.
22803
4.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY
Install the fuel injection pump cover sub-assembly to the supply pump assembly.
23804D
5.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)
Install 2 new gaskets and tighten the 2 union bolts in the order shown in the illustration.
23273H
6.INSTALL NO. 2 FUEL HOSE
Install the No. 2 fuel hose to the supply pump assembly and No. 3 nozzle leakage pipe assembly, and slide the 2 clamps to secure it.
23271H
7.INSTALL NO. 1 FUEL HOSE
Install the No. 1 fuel hose to the supply pump assembly and No. 2 fuel pipe, and slide the 2 clamps to secure it.
16620
8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
16711
9.INSTALL FAN SHROUD
16470
10.INSTALL RADIATOR RESERVOIR
44369A
11.INSTALL NO. 1 OIL RESERVOIR BRACKET
44360
12.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
16571C
13.INSTALL NO. 1 RADIATOR HOSE
17362B
14.INSTALL NO. 2 AIR TUBE
17344E
15.INSTALL NO. 4 AIR HOSE
17111
16.INSTALL INTAKE MANIFOLD
17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
18.BLEED AIR FROM FUEL SYSTEM
19.INSPECT FOR FUEL LEAK
51441
20.INSTALL NO. 1 ENGINE UNDER COVER