Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM33K0E _51 Engine / Hybrid System _043566 1KD-FTV ENGINE CONTROL _0222113 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P2563  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  P2588  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low  P2589  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High  


DESCRIPTION

Variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the turbo motor driver. The turbo motor driver determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A158417E07
4.198,1.458 4.198,0.615 false 4.198,0.615 4.552,0.615 false 1.125,2.719 0.833,3.323 true 1.344,3.115 1.469,3.354 true 1.115,2.177 0.667,1.323 0.667,1.323 0.813,1.323 true 1.344,1.781 1.552,1.313 1.552,1.313 1.688,1.313 true 0.49,3.885 2.313,4.354 1.823,0.469 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.865,1.25 1.427,1.479 0.563,0.229 10 false IC No. 1 0.583,3.385 1.177,3.615 0.594,0.229 10 false IC No. 2 3.01,1.885 3.406,2.094 0.396,0.208 10 false VTA1 3,2.188 3.427,2.417 0.427,0.229 10 false VNE2 3,1.552 3.427,1.771 0.427,0.219 10 false VNVC 3,2.813 3.427,3.031 0.427,0.219 10 false VTA2 3.01,3.146 3.385,3.354 0.375,0.208 10 false E2S 3,2.5 3.406,2.708 0.406,0.208 10 false VCS 2.885,3.531 3.688,3.906 0.802,0.375 10 false Turbo Motor Driver 4.708,3.635 5.229,3.875 0.521,0.24 10 false Closed 5.708,3.635 6.302,3.865 0.594,0.229 10 false Opened 1.75,1.24 2.26,1.51 0.51,0.271 10 false Magnet 4.625,0.51 6.302,0.979 1.677,0.469 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.052,2.677 0.521,3.063 0.469,0.385 10 false Sensor Vane 4.094,1.563 4.354,1.74 0.26,0.177 10 false 4.5 4.094,2.427 4.365,2.604 0.271,0.177 10 false 0.5 1.396,3.375 1.906,3.604 0.51,0.229 10 false Magnet 4.76,3.302 6.177,3.51 1.417,0.208 10 true Nozzle Vane Position

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2563 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance Difference between VTA1 and VTA2 voltage 0.8 V or more for 0.5 seconds or more
(1 trip detection logic)
Nozzle vane position sensor (Turbocharger sub-assembly) Comes on DTC stored
P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low VTA1 voltage 0.5 V or less for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored
P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High VTA1 voltage 4.5 V or more for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored
P2588 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low VTA2 voltage 0.5 V or less for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored
P2589 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High VTA2 voltage 4.5 V or more for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P2563, P2564, P2565, P2588, P2589
DTC Detection Drive Pattern Ignition switch to ON for 1 seconds

WIRING DIAGRAM

A255060E15
0.375,2.958 0.729,3.115 0.354,0.156 10 false C92 0.385,3.115 2.25,3.292 1.865,0.177 10 false Nozzle Vane Position Sensor 5.563,3.125 6.802,3.292 1.24,0.167 10 false Turbo Motor Driver 1.563,0.438 1.938,0.635 0.375,0.198 10 false VTA1 5.583,0.365 5.969,0.563 0.385,0.198 10 false VTA1 1.531,0.865 1.938,1.031 0.406,0.167 10 false VNE2 5.583,0.771 5.99,0.938 0.406,0.167 10 false VNE2 1.521,1.281 1.969,1.469 0.448,0.188 10 false VNVC 5.583,1.198 6.031,1.385 0.448,0.188 10 false VNVC 1.542,1.708 1.969,1.885 0.427,0.177 10 false VTA2 5.583,1.615 6.01,1.792 0.427,0.177 10 false VTA2 1.615,2.146 1.969,2.313 0.354,0.167 10 false E2S 5.583,2.042 5.938,2.208 0.354,0.167 10 false E2S 1.604,2.542 1.969,2.708 0.365,0.167 10 false VCS 5.583,2.458 5.927,2.625 0.344,0.167 10 false VCS 5.542,2.979 5.865,3.167 0.323,0.188 10 false C91 1.99,2.021 2.115,2.177 0.125,0.156 10 false 5 1.99,1.594 2.115,1.75 0.125,0.156 10 false 4 1.99,1.167 2.115,1.323 0.125,0.156 10 false 3 1.99,0.75 2.115,0.906 0.125,0.156 10 false 2 1.99,0.365 2.115,0.521 0.125,0.156 10 false 1 1.99,2.469 2.115,2.625 0.125,0.156 10 false 6 5.385,0.354 5.542,0.542 0.156,0.188 10 false 9 5.385,0.76 5.51,0.948 0.125,0.188 10 false 8 5.385,1.177 5.542,1.365 0.156,0.188 10 false 1 5.344,1.583 5.563,1.771 0.219,0.188 10 false 10 5.344,2.021 5.563,2.208 0.219,0.188 10 false 11 5.385,2.448 5.542,2.635 0.156,0.188 10 false 6

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2563, P2564, P2565, P2588 AND/OR P2589)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
P2563, P2564, P2565, P2588 and/or P2589 is output A
P2563, P2564, P2565, P2588 and/or P2589 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - TURBO MOTOR DRIVER)

B

2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - TURBO MOTOR DRIVER)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the turbo motor driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C92-1 (VTA1) - C91-9 (VTA1) Always Below 1 Ω
C92-2 (VNE2) - C91-8 (VNE2) Always Below 1 Ω
C92-3 (VNVC) - C91-1 (VNVC) Always Below 1 Ω
C92-4 (VTA2) - C91-10 (VTA2) Always Below 1 Ω
C92-5 (E2S) - C91-11 (E2S) Always Below 1 Ω
C92-6 (VCS) - C91-6 (VCS) Always Below 1 Ω
C92-1 (VTA1) or C91-9 (VTA1) - Body ground Always 10 kΩ or higher
C92-2 (VNE2) or C91-8 (VNE2) - Body ground Always 10 kΩ or higher
C92-3 (VNVC) or C91-1 (VNVC) - Body ground Always 10 kΩ or higher
C92-4 (VTA2) or C91-10 (VTA2) - Body ground Always 10 kΩ or higher
C92-5 (E2S) or C91-11 (E2S) - Body ground Always 10 kΩ or higher
C92-6 (VCS) or C91-6 (VCS) - Body ground Always 10 kΩ or higher



d.

Reconnect the turbo motor driver connector.


e.

Reconnect the nozzle vane position sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK TURBO MOTOR DRIVER (SENSOR POWER SOURCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK TURBO MOTOR DRIVER (SENSOR POWER SOURCE)
a.
A251333C14
0.417,0.865 0.854,1.125 0.438,0.26 1.417,1.052 0.792,1.677 false 1.563,1.063 1.375,1.635 false 1.875,1.063 2,1.604 false 2.021,1.063 2.625,1.625 false 0.167,0.104 0.406,0.271 0.24,0.167 10 false *a 0.5,0.917 0.792,1.115 0.292,0.198 10 false C92 0.563,1.677 0.948,1.875 0.385,0.198 10 false VNE2 1.875,1.667 2.219,1.865 0.344,0.198 10 false E2S 1.146,1.677 1.563,1.875 0.417,0.198 10 false VNVC 2.5,1.656 2.844,1.854 0.344,0.198 10 false VCS
*a Front view of with harness connector
(to Nozzle Vane Position Sensor)


Disconnect the nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C92-3 (VNVC) - C92-2 (VNE2) Ignition switch ON 4.5 to 5.5 V
C92-6 (VCS) - C92-5 (E2S) Ignition switch ON 4.5 to 5.5 V



d.

Reconnect the nozzle vane position sensor connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT TURBO MOTOR DRIVER (VTA1, VTA2 VOLTAGE)

NG

5.REPLACE TURBO MOTOR DRIVER
4.INSPECT TURBO MOTOR DRIVER (VTA1, VTA2 VOLTAGE)
A158418C32
0.74,0.823 1.167,1.104 0.427,0.281 1.906,2.333 2.469,2.76 false 1.781,2.344 2.073,2.771 false 1.615,2.333 1.49,2.802 false 1.479,2.333 1.104,2.802 false 0.813,0.885 1.094,1.063 0.281,0.177 10 false C91 2,2.802 2.406,2.979 0.406,0.177 10 false VTA1 1.24,2.823 1.646,3 0.406,0.177 10 false VTA2 2.458,2.802 2.865,2.979 0.406,0.177 10 false VNE2 0.854,2.813 1.177,2.99 0.323,0.177 10 false E2S 0.385,0.292 0.583,0.469 0.198,0.177 10 false *a
*a Component with harness connected
(Turbo Motor Driver)


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C91-9 (VTA1) - C91-8 (VNE2) Ignition switch ON 0.5 to 4.5 V
C91-10 (VTA2) - C91-11 (E2S) Ignition switch ON 0.5 to 4.5 V



c.

Check the difference between the voltage values.

Result:

Voltage difference between VTA1 and VTA2 is within 0.8 V



Result:
Proceed to
OK
NG



OK

5.REPLACE TURBO MOTOR DRIVER

NG

7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)
5.REPLACE TURBO MOTOR DRIVER

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2563, P2564, P2565, P2588 AND/OR P2589)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2563, P2564, P2565, P2588 AND/OR P2589)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Start the engine.


e.

Drive the vehicle with a city driving pattern at least 10 minutes.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Read the DTCs.

Result:
Result Proceed to
P2563, P2564, P2565, P2588 and/or P2589 output again A
No DTC is output B




A

7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

B

END

7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Start the engine.


e.

Drive the vehicle with a city driving pattern at least 10 minutes.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END