While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).
Refer to DTC P0617
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0617
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read Starter Count before replacing the engine stop and start ECU, perform the replacement procedure, and then write Starter Count to the newly installed engine stop and start ECU.
When replacing the engine stop and start ECU or the air conditioning amplifier assembly, initialize and learn the engine stop and start ECU air conditioning information.
When replacing the engine stop and start ECU or airbag ECU assembly (G sensor), initialize and learn the engine stop and start ECU G sensor zero point learned information.
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG (for Automatic Transmission) |
| NG (for Manual Transmission) |
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>1KD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
for DENSO Made
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>INSPECTION
for BOCH Made
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for DENSO Made
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for BOSCH Made
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (ST NO. 1 relay terminal holder) - C26-1 | Always | Below 1 Ω |
| 3 (ST NO. 1 relay terminal holder) or C26-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-1 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST NO. 1 relay terminal holder) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the park/neutral position switch assembly connector.
Disconnect the clutch start switch connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-5 - 2 (ST NO. 1 relay terminal holder) | Always | Below 1 Ω |
| B2-1 - 2 (ST NO. 1 relay terminal holder) | Always | Below 1 Ω |
| G17-37 (STA) - 2 (ST NO. 1 relay terminal holder) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (ST NO. 1 relay terminal holder) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-5 - G130-7 (STA) | Always | Below 1 Ω |
| C22-5 or G130-7 (STA) or 2 (ST NO. 1 relay terminal holder) or G17-37 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - C22-4 | Always | Below 1 Ω |
| G17-16 (STAR) - G130-6 (NSW) | Always | Below 1 Ω |
| G17-16 (STAR) or C22-4 or G130-6 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the clutch start switch connector.
Disconnect the ECM connector.
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B2-1 - G130-7 (STA) | Always | Below 1 Ω |
| B2-1 or G130-7 (STA) or 2 (ST NO. 1 relay terminal holder) or G17-37 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the clutch start switch connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - B2-2 | Always | Below 1 Ω |
| G17-16 (STAR) or B2-2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG