Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM33K0E _58 Vehicle Interior _043547 DOOR LOCK _0222453 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 69318D 1.INSTALL DOOR LOCK WIRING HARNESS SEAL

NOTICE:
·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock assembly.

·

When reusing a removed rear door lock assembly, replace the door lock wiring harness seal with a new one.



a.
B438886

Install a new door lock wiring harness seal to the rear door lock assembly LH.


Hide 69780B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B438887C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the rear door inside locking cable assembly LH to the rear door lock assembly LH.


Hide 69740D 3.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B438888C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the rear door lock remote control cable assembly LH to the rear door lock assembly LH.


Hide 69038A 4.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH

a.
B438883

Attach the clamp and claw to install the rear door lock cover sub-assembly LH.


Hide 69340 5.INSTALL REAR DOOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door lock assembly LH.


b.
B438893C01
2.021,2.052 2.281,2.052 2.281,2.052 2.604,2.25 true 1.823,1.969 2.135,2.167 0.313,0.198 10 false *a
*a Release Plate
V100135

"Torx" Screw
V100136

Connector
V113147

Install in this Direction


Insert the rear door lock assembly LH into the rear door outside handle frame sub-assembly LH release plate, and set it to the rear door panel LH.

HINT:

Make sure that the rear door outside handle frame sub-assembly LH release plate is securely connected to the rear door lock assembly LH.



c.

Using a T30 "TORX" socket wrench, install the rear door lock assembly LH with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 67836H 6.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

Hide 68104 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 67408E 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 9.INSTALL REAR DOOR GLASS RUN LH

Hide 67842E 10.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 67604 11.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 69284D 12.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 13.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 74260 14.INSTALL REAR ARMREST ASSEMBLY LH

Hide 67674A 15.INSTALL REAR DOOR FRAME GARNISH LH

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION