Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM33K0E _59 Vehicle Exterior _043559 DOOR / HATCH _0219595 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67837C 4.INSTALL REAR DOOR DUST PROOF SEAL

a.
B438866

Attach the claw to install 3 new rear door dust proof seals.


Hide 67872 5.INSTALL REAR DOOR WEATHERSTRIP LH

a.
B438865C02
0,0 0,0 false
V100155

Double-sided Tape


Attach the clip to install a new rear door weatherstrip LH.


b.

Remove the peeling paper from double-sided tape and press the double-sided tape to the rear door panel LH.


Hide 68640A 6.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door check assembly LH.


b.

When reusing a bolt:

i.

Clean the threads of the bolt (B) with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B438815C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the rear door check assembly LH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67003C 7.INSTALL REAR DOOR PANEL CUSHION

a.
B438814

Attach the claw to install 2 new rear door panel cushions.


Hide 69204A 8.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door outside handle frame sub-assembly LH.


b.
B438751C01
2.24,0.531 2.24,0.198 2.24,0.198 2.49,0.198 true 2.24,0.844 2.24,1.177 2.24,1.177 2.49,1.177 true 1.115,0.74 1.115,1.073 1.115,1.073 1.365,1.073 true 1.333,0.969 1.646,1.167 0.313,0.198 10 true *a 2.479,0.104 2.792,0.302 0.313,0.198 10 true *b 2.458,1.083 2.771,1.281 0.313,0.198 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Attach the grommet and guide to install the rear door outside handle frame sub-assembly LH as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 9.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B438753C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door rear outside handle pad.


Hide 69241G 10.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B438752C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door front outside handle pad.


Hide 69240 11.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B438765C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door outside handle assembly LH as shown in the illustration.


Hide 69227M 12.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B438764C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door outside handle cover as shown in the illustration.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69318D 13.INSTALL DOOR LOCK WIRING HARNESS SEAL

Hide 69740D 14.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Hide 69780B 15.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

Hide 69038A 16.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH

Hide 69340 17.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 67836H 18.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

a.
B438808

Install the rear door lock child protection cover LH.


Hide 85720G 19.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69804 20.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door window regulator sub-assembly LH.


b.

Temporarily install the temporarily bolt to the rear door window regulator sub-assembly LH.


c.
B438807C02
0,0 0,0 false
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt


Install the rear door window regulator sub-assembly LH with the 3 bolts and temporary bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the rear door window regulator sub-assembly LH as it may become damaged.



d.

Connect the connector.


Hide 75740 21.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 75724 22.INSTALL REAR DOOR REAR BELT MOULDING LH

Hide 68189 23.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B438750

Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.


Hide 68124C 24.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.
B438763C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH.


Hide 68104 25.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B438761C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly LH as shown in the illustration.


b.
B438762

Install the rear door glass sub-assembly LH to the rear door window regulator sub-assembly LH as shown in the illustration.

NOTICE:

Be careful not to damage the glass.



Hide 67408E 26.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.
B438803C02
0,0 0,0 false
V100135

Bolt
V100136

Screw


Lift up the rear door weatherstrip LH and install the screw.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


b.

Install the rear door window division bar sub-assembly LH with the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68152C 27.INSTALL REAR DOOR GLASS RUN LH

a.
B438802

Attach the guide to install a new rear door glass run LH.


Hide 28.INSTALL SCREW GROMMET

a.
B438801

Attach the claw to install 2 new screw grommets.


Hide 67842E 29.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the rear door panel.


b.
B438760C01
0.729,0.427 0.729,0.24 0.729,0.24 0.542,0.24 true 2.698,0.448 2.698,0.26 2.698,0.26 2.865,0.26 true 0.396,0.146 0.615,0.344 0.219,0.198 10 true *a 2.792,0.177 3.01,0.375 0.219,0.198 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the rear door inside locking cable assembly LH and rear door lock remote control cable assembly LH through a new rear door service hole cover LH, and then attach the rear door service hole cover LH using the reference points on the rear door panel.

HINT:
·

Securely install the rear door service hole cover LH to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the rear door service hole cover LH.

·

After installing the rear door service hole cover LH, check the seal quality.




Hide 86160B 30.INSTALL REAR SPEAKER ASSEMBLY

Hide 68174A 31.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B438759C01
0,0 0,0 false
V113147

Install in this Direction


Install a new rear door inner glass weatherstrip LH to the rear door trim board sub-assembly LH and fold down the claw in the directions indicated by the arrows in the illustration.


Hide 69206C 32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B438758C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door inside handle sub-assembly LH to the rear door trim board sub-assembly LH.


Hide 67604 33.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B438766C01
2.76,1 2.479,0.438 2.479,0.438 2.063,0.438 true 2.781,1.302 2.51,1.927 2.51,1.927 2,1.927 true 1.833,1.833 2.146,2.031 0.313,0.198 10 true *2 1.885,0.323 2.198,0.521 0.313,0.198 10 true *1
*1 Rear Door Inside Locking Cable Assembly LH
*2 Rear Door Lock Remote Control Cable assembly LH
V113147

Install in this Direction


Attach the clamp to connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.


b.
B438757C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.
B438756

Attach the clip to install the rear door trim board sub-assembly LH.


d.
B438795

Install the 3 screws.


Hide 69284D 34.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B438755

Attach the claw to install the rear door inside handle bezel plug LH.


Hide 67666C 35.INSTALL REAR DOOR TRIM REFLECTOR LH (w/ Reflex Reflector Assembly)

a.
B412118C05
0.094,0.083 0.406,0.281 0.313,0.198 10 true *A 0.115,2.542 0.427,2.74 0.313,0.198 10 true *B
*A for LH Side
*B for RH Side
V100155

Protective Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and claw to install the rear door trim reflector as shown in the illustration.


b.

Remove the protective tape.


Hide 81230 36.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 84810D 37.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 38.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.
B438754C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the rear power window regulator switch assembly with rear door armrest base panel as shown in the illustration.


Hide 74260 39.INSTALL REAR ARMREST ASSEMBLY LH

a.
B438767C01
0,0 0,0 false
V100135

Order of Installation
V113147

Install in this Direction


Attach the claw and clip to install the rear armrest assembly LH.


Hide 67674A 40.INSTALL REAR DOOR FRAME GARNISH LH

a.
B438791

Attach the clip and claw to install the rear door frame garnish LH.


Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION