Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0222678 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1403

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)


C1408 Open or Short in Rear Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C243493E57
5.979,0.688 6.542,1.198 0.563,0.51 10 false RR+ 5.979,1.26 6.365,1.51 0.385,0.25 10 false RR- 5.979,2.729 6.458,3.094 0.479,0.365 10 false RL+ 5.979,3.292 6.417,3.646 0.438,0.354 10 false RL- 5.688,0.573 5.938,0.802 0.25,0.229 10 false 16 5.698,1.146 5.958,1.385 0.26,0.24 10 false 15 2.365,1.125 2.531,1.323 0.167,0.198 10 false 1 1.125,1.125 1.354,1.344 0.229,0.219 10 false 2 5.677,2.594 6.042,2.927 0.365,0.333 10 false 29 5.667,3.156 5.979,3.5 0.313,0.344 10 false 28 1.26,3.604 2.729,3.927 1.469,0.323 10 false Rear Speed Sensor LH 1.271,1.563 2.708,1.875 1.438,0.313 10 false Rear Speed Sensor RH 5.438,4.083 7.01,4.563 1.573,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.438,3.885 5.76,4.104 0.323,0.219 10 false A4 0.958,1.552 1.333,1.833 0.375,0.281 10 false O8 0.958,3.604 1.292,3.865 0.333,0.26 10 false O9 2.375,3.156 2.531,3.333 0.156,0.177 10 false 1 1.125,3.146 1.333,3.354 0.208,0.208 10 false 2 1.375,1.26 1.792,1.5 0.417,0.24 10 false RR+ 2,1.26 2.552,1.594 0.552,0.333 10 false RR- 1.375,3.292 1.688,3.469 0.313,0.177 10 false RL+ 2,3.292 2.313,3.469 0.313,0.177 10 false RL-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
RL Speed Open Rear speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1407 and C1408 are not output
DTCs C1407 and/or C1408 are output



DTCs C1407 and C1408 are not output

DTCs C1407 and/or C1408 are output

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A4 skid control ECU (brake actuator assembly) connector and the O8 and/or O9 rear speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A4-16 (RR+) - O8-2 (RR+) Always Below 1 Ω
A4-15 (RR-) - O8-1 (RR-) Always Below 1 Ω
A4-16 (RR+) or O8-2 (RR+) - Body ground Always 10 kΩ or higher
A4-15 (RR-) or O8-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A4-29 (RL+) - O9-2 (RL+) Always Below 1 Ω
A4-28 (RL-) - O9-1 (RL-) Always Below 1 Ω
A4-29 (RL+) or O9-2 (RL+) - Body ground Always 10 kΩ or higher
A4-28 (RL-) or O9-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
C238771C08
0.823,0.292 1.104,0.49 0.281,0.198 2.406,0.292 2.688,0.49 0.281,0.198 2.979,1.792 2.708,1.323 true 1.406,1.719 1.135,1.25 true 1.156,0.313 1.469,0.469 0.313,0.156 10 false *A 2.708,0.281 3.021,0.438 0.313,0.156 10 false *B 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 2.458,0.313 2.698,0.521 0.24,0.208 10 false O9 0.865,0.313 1.104,0.521 0.24,0.208 10 false O8 1.344,1.75 1.729,1.948 0.385,0.198 10 false RR+ 2.917,1.802 3.375,2 0.458,0.198 10 false RL+
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
O8-2 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
O9-2 (RL+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG