| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1268 | Transfer L4 Position Switch Circuit | Either of the following is detected:
1.
No signal is input to the EXI4 terminal of the skid control ECU. 2.
The skid control ECU receives an L4 abnormal status signal from the 4 wheel drive control ECU via CAN. |
·
L4 detection switch (Transfer shift actuator assembly) ·
L4 detection switch circuit ·
Skid control ECU (Brake actuator assembly) ·
4 wheel drive control ECU ·
Touch select 2-4 and high-low system |
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
When DTC U0114 is output together with DTC C1268, inspect and repair the trouble areas indicated by DTC U0114 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073
Turn the 4WD control switch (transfer position switch) to L4, and then drive the vehicle and check that there are no problems with the touch select 2-4 and high-low system.
There are no problems with the touch select 2-4 and high-low system.
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the A4 skid control ECU (brake actuator assembly) connector.
Turn the 4WD control switch (transfer position switch) to L4.
Disconnect the C41*1, G57*2 or G158*3 ECM connector.
*1: for 1GD-FTV
*2: for 2TR-FE
*3: for 1GR-FE
Disconnect the G131* TCM connector.
*: for 1KD-FTV
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
| *a | Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A4-5 (EXI4) - Body ground | ·
Ignition switch ON ·
4WD control switch (transfer position switch) set to L4 |
Below 1.5 V |
Reconnect the A4 skid control ECU (brake actuator assembly) connector.
Reconnect the C41*1, G57*2 or G158*3 ECM connector.
*1: for 1GD-FTV
*2: for 2TR-FE
*3: for 1GR-FE
Reconnect the G131* TCM connector.
*: for 1KD-FTV
Turn the 4WD control switch (transfer position switch) to H2 or H4.
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Disconnect the C41*1, G57*2 or G158*3 ECM connector.
*1: for 1GD-FTV
*2: for 2TR-FE
*3: for 1GR-FE
Disconnect the G131* TCM connector.
*: for 1KD-FTV
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A4-5 (EXI4) - Body ground | ·
Ignition switch ON ·
4WD control switch (transfer position switch) set to H2 or H4 |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Reconnect the A4 skid control ECU (brake actuator assembly) connector.
Reconnect the C41*1, G57*2 or G158*3 ECM connector.
*1: for 1GD-FTV
*2: for 2TR-FE
*3: for 1GR-FE
Reconnect the G131* TCM connector.
*: for 1KD-FTV
Turn the ignition switch to ON.
Clear the DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Turn the 4WD control switch (transfer position switch) to H2 or H4.
Turn the 4WD control switch (transfer position switch) to L4, drive the vehicle, and then check for DTCs.
| Proceed to |
|---|
| DTC is output |
| DTC is not output |
DTC is output
DTC is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING