Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0222679 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When voltage at terminal IG1 is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more.
·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C325963E01
4.833,0.958 5.292,1.156 0.458,0.198 10 false STP 4.854,2.219 5.313,2.417 0.458,0.198 10 false GND1 4.563,0.823 5.021,1.021 0.458,0.198 10 false 28 4.625,2.083 5.083,2.281 0.458,0.198 10 false 1 4.865,2.958 5.323,3.156 0.458,0.198 10 false A3 4.875,3.135 6.552,3.51 1.677,0.375 10 false Skid control ECU (Brake actuator assembly) 0.771,0.958 2.448,1.333 1.677,0.375 10 false from Stop Light Switch 0.927,1.635 2.604,2.01 1.677,0.375 10 false to Stop Light Circuit 4.635,1.083 4.885,1.375 0.25,0.292 10 false B 4.156,1.083 4.406,1.375 0.25,0.292 10 false A

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C260095C40
0.177,0.917 0.51,1.177 0.333,0.26 1.427,1.833 1.635,1.396 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.26,0.969 0.573,1.167 0.313,0.198 10 false A3 1.135,1.792 1.438,2 0.302,0.208 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A3 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A3-28 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
Stop light switch OFF (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT CIRCUIT)

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A3 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
d.

Turn the ignition switch off.


e.

Start the engine.


f.

Depress the brake pedal several times to test the stop light circuit.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTC C1425 is not output
DTC C1425 is output



DTC C1425 is not output

DTC C1425 is output