The radio and display receiver assembly a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2 to use for adjusting the vehicle position on the display.
*1: for Automatic Transmission
*2: for Manual Transmission
Inspect the fuses for circuits related to this system before performing the following procedure.
Enter the "Vehicle Signal Check Mode" screen.
Refer to check Vehicle Signal in Operation Check.
Check that the display changes between ON and OFF according to the shift lever position.
| Shift Lever Position | Display |
|---|---|
| R | ON |
| Except R | OFF |
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-2 (REV) - Body ground | Ignition switch ON, shift lever in R | 11 to 14 V |
| G100-2 (REV) - Body ground | Ignition switch ON, shift lever any position other than in R | Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
B
C
Disconnect the G100 radio and display receiver assembly connector.
Disconnect the C22 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G100-2 (REV) - C22-1 (RL) | Always | Below 1 Ω |
| G100-2 (REV) or C22-1 (RL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C22-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
A750F: Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
AC60E: Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
AC60F: Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
NG
Disconnect the G100 radio and display receiver assembly connector.
Disconnect the C11 back-up light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G100-2 (REV) - C11-1 | Always | Below 1 Ω |
| G100-2 (REV) or C11-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back-up Light Switch Assembly) |
Disconnect the back-up light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C11-2 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG