Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224644 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the body ECU transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

E318152E02
6.021,0.385 6.333,0.583 0.313,0.198 10 false SH 5.781,0.385 6.094,0.583 0.313,0.198 10 false 10 4.698,0.792 5.01,0.99 0.313,0.198 10 false 2P 4.698,0.948 5.813,1.469 1.115,0.521 10 false Instrument Panel Junction Block Assembly 5.938,1.708 6.302,1.906 0.365,0.198 10 false A 5.927,1.865 6.99,2.156 1.063,0.292 10 false Body ECU 4.896,0.385 5.208,0.583 0.313,0.198 10 false 14 4.083,0.385 4.396,0.583 0.313,0.198 10 false 2 4.083,0.781 4.396,0.979 0.313,0.198 10 false 3 3.177,0.385 3.49,0.583 0.313,0.198 10 false 1 3.177,0.771 3.49,0.969 0.313,0.198 10 false 5 1.844,0.646 2.74,0.885 0.896,0.24 10 false ECU-B NO.3 0.417,0.49 1.698,0.708 1.281,0.219 10 false from Battery 3.146,1.688 4.427,1.906 1.281,0.219 10 false A31 3.135,1.833 4.01,2.24 0.875,0.406 10 false Security Horn Assembly 2.99,1.208 4.479,1.448 1.49,0.24 10 false Horn Relay (S-HORN) 4.24,1.563 4.552,1.76 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Door control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.INSPECT SECURITY HORN ASSEMBLY


Result:
Proceed to
OK
NG



OK

2.INSPECT HORN RELAY (S-HORN)

NG

2.INSPECT HORN RELAY (S-HORN)
a.
B256934C05
2.198,0.906 2,0.583 true 2.823,1 2.594,0.594 true 2.146,1.469 1.948,1.823 true 2.51,1.219 2.729,1.75 true 0.104,0.083 0.417,0.396 0.313,0.313 10 false *1 0.323,1.458 0.573,1.75 0.25,0.292 10 false 5 1.313,0.667 1.594,0.917 0.281,0.25 10 false 2 0.313,0.667 0.51,0.906 0.198,0.24 10 false 1 1.313,1.469 1.563,1.708 0.25,0.24 10 false 3 2.75,1.771 2.969,1.99 0.219,0.219 10 false 5 1.833,1.771 2.063,2 0.229,0.229 10 false 1 1.917,0.417 2.208,0.688 0.292,0.271 10 false 2 2.542,0.417 2.813,0.708 0.271,0.292 10 false 3
*1 Horn Relay (S-HORN)


Remove the horn relay (S-HORN).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE HORN RELAY (S-HORN)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343149C15
2.24,0.417 2.573,0.625 0.333,0.208 5.604,0.26 5.938,0.469 0.333,0.208 2.375,1.26 2.542,0.948 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.365,0.448 2.677,0.646 0.313,0.198 10 false A 5.656,0.281 5.969,0.479 0.313,0.198 10 false 2P 2.26,1.292 2.573,1.49 0.313,0.198 10 false SH
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2P-14 - A-10 (SH) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - HORN RELAY (S-HORN))

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BATTERY - HORN RELAY (S-HORN))
a.

Remove the horn relay (S-HORN).


b.
B341518

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Always 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HORN RELAY (S-HORN) - SECURITY HORN ASSEMBLY AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HORN RELAY (S-HORN) - SECURITY HORN ASSEMBLY AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the horn relay (S-HORN).


b.

Disconnect the A31 security horn assembly connector.


c.

Disconnect the 2P instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A31-1 Always Below 1 Ω
Relay terminal 2 - 2P-14 Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher
Relay terminal 2 - Body ground Always 10 kΩ or higher
A31-1 - Body ground Always 10 kΩ or higher
2P-14 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR