The body ECU determines the ignition switch position (LOCK, ACC, ON) based on signals from the IG or ACC circuit.
Inspect the fuses for circuits related to this system before performing the following procedure.
w/ Door control Battery:
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
w/ Automatic Light Control System:
If the body ECU has been replaced, it is necessary to initialize the body ECU.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Remove the ignition or starter switch assembly.
for 2TR-FE
Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>REMOVAL
for 1GD-FTV
Click hereEngine / Hybrid System>1GD-FTV STARTING>IGNITION SWITCH>REMOVAL
for 1KD-FTV
Click hereEngine / Hybrid System>1KD-FTV STARTING>IGNITION SWITCH>REMOVAL
Inspect the ignition or starter switch assembly.
for 2TR-FE
Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>INSPECTION
for 1GD-FTV
Click hereEngine / Hybrid System>1GD-FTV STARTING>IGNITION SWITCH>INSPECTION
for 1KD-FTV
Click hereEngine / Hybrid System>1KD-FTV STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>REMOVAL
for 1GD-FTV
Click hereEngine / Hybrid System>1GD-FTV STARTING>IGNITION SWITCH>REMOVAL
for 1KD-FTV
Click hereEngine / Hybrid System>1KD-FTV STARTING>IGNITION SWITCH>REMOVAL
Disconnect the ignition or starter switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G133-5 (AM1) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the body ECU.
for LHV:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Connect the 2D, 2E and 2J instrument panel junction block assembly connectors.
Disconnect the G133 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G133-8 (IG1) - A-7 (IG) | Always | Below 1 Ω |
| G133-8 (IG1) - Body ground | Always | 10 kΩ or higher |
| A-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Disconnect the 2D, 2E and 2J instrument panel junction block assembly connectors.
Disconnect the G133 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G133-8 (IG1) - 2E-1 | Always | Below 1 Ω |
| 2D-7 - 2D-5 | Always | Below 1 Ω |
| G133-8 (IG1) - Body ground | Always | 10 kΩ or higher |
| 2D-7 - Body ground | Always | 10 kΩ or higher |
| 2J-5 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG