Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224644 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the body ECU which causes the intrusion sensor to stop operating.

WIRING DIAGRAM

B433600E01
1.813,1.031 4.469,1.333 2.656,0.302 10 false Intrusion Sensor Cancel Switch 1.781,0.74 2.24,0.938 0.458,0.198 10 false GND 3.469,0.75 3.927,0.948 0.458,0.198 10 false IND2 5.271,0.844 5.729,1.042 0.458,0.198 10 false SSW1 5.323,1.583 6.708,2 1.385,0.417 10 false Body ECU 5.313,1.417 5.771,1.615 0.458,0.198 10 false G33 2.188,1.417 2.646,1.615 0.458,0.198 10 false Q2 2.188,1.583 3.854,1.979 1.667,0.396 10 false Map Light Assembly 1.615,0.76 2.073,0.958 0.458,0.198 10 false 3 3.854,0.75 4.313,0.948 0.458,0.198 10 false 7 5.01,0.76 5.469,0.958 0.458,0.198 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BODY ECU - MAP LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G33 body ECU connector.


b.

Disconnect the Q2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-10 (SSW1) - Q2-7 (IND2) Always Below 1 Ω
Q2-3 (GND) - Body ground Always Below 1 Ω
G33-10 (SSW1) - Body ground Always 10 kΩ or higher
Q2-7 (IND2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.
E320541E01
2,1.01 2.427,0.427 true 1.281,1.01 0.813,0.417 true 0.583,0.25 1.344,0.479 0.76,0.229 10 false IND2 2.344,0.229 2.802,0.427 0.458,0.198 10 false GND

Remove the map light assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>MAP LIGHT BULB>REPLACEMENT


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (IND2) - 3 (GND) Intrusion sensor cancel switch not pressed 10 kΩ or higher
7 (IND2) - 3 (GND) Intrusion sensor cancel switch pressed Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)