Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224644 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the body ECU cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or back door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or back door, or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

A window or the sliding roof is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

B433601E01
1.115,0.396 2.948,0.594 1.833,0.198 10 false from Battery 2.865,0.583 4.698,0.781 1.833,0.198 10 false ECU-B NO. 1 1.5,1.344 3.427,1.906 1.927,0.563 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 3.74,1.271 5.573,1.469 1.833,0.198 10 false +B2 3.708,1.813 5.542,2.01 1.833,0.198 10 false IND1 1.375,2.479 3.208,2.677 1.833,0.198 10 false Q2 1.385,2.635 3.219,2.833 1.833,0.198 10 false Map Light Assembly 5.604,2.49 6.51,2.719 0.906,0.229 10 false G34 5.604,2.656 6.583,2.865 0.979,0.208 10 false Body ECU 0.938,1.542 2.771,1.74 1.833,0.198 10 false GND 4.094,1.25 5.927,1.448 1.833,0.198 10 false 16 5.385,1.802 5.667,2 0.281,0.198 10 false 12 4.115,1.792 4.396,1.99 0.281,0.198 10 false 8 0.74,1.542 1.021,1.74 0.281,0.198 10 false 3 5.635,1.906 6.448,2.219 0.813,0.313 10 false ISIF

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Door control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)
a.
B419470C01
1.49,0.104 1.979,0.406 0.49,0.302 2.479,1.323 2.896,0.906 true 0.573,0.75 1.406,1.031 true 1.625,0.177 1.938,0.375 0.313,0.198 10 false Q2 0.24,0.646 0.604,0.854 0.365,0.208 10 false GND 2.948,0.729 3.365,1.073 0.417,0.344 10 false +B2
*a Front view of wire harness connector
(to Map Light Assembly)


Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q2-16 (+B2) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IND1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WAVEFORM (INTRUSION SENSOR [THEFT WARNING ULTRASONIC SENSOR]) (IND1)
a.

Using an oscilloscope, check the waveform.

B419467C01
3.292,0.073 3.719,0.302 0.427,0.229 2.292,0.656 3.042,1.104 true 1.656,2.688 1.906,2.885 true 2.188,2.688 2.438,2.885 true 3.406,0.094 3.719,0.292 0.313,0.198 10 false Q2 1.927,0.573 2.417,0.844 0.49,0.271 10 false IND1 0.135,0.125 0.625,0.396 0.49,0.271 10 false *a 1.458,2.583 1.948,2.854 0.49,0.271 10 false *b 2,2.594 2.49,2.865 0.49,0.271 10 false *c 4.021,2.604 4.51,2.875 0.49,0.271 10 false *d 4.021,3.219 4.51,3.49 0.49,0.271 10 false *e 2.094,3.25 2.583,3.521 0.49,0.271 10 false *f 2.542,3.25 3.031,3.521 0.49,0.271 10 false *g 2.646,3.604 3.135,3.875 0.49,0.271 10 false *h 1.531,4.198 2.021,4.469 0.49,0.271 10 false *i 3.906,4.208 4.396,4.479 0.49,0.271 10 false *j 1.031,2.479 1.521,2.75 0.49,0.271 10 false HI 1.031,2.958 1.521,3.229 0.49,0.271 10 false LO
*a Component with harness connected
(Map Light Assembly)
*b IND1 Initial Signal
*c IND1 Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition
Item Content
Tester Connection Q2-8 (IND1) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the body ECU.

·

If the waveform output remains LO, there may be a problem with the body ECU, as there is no input from the body ECU.



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Result Proceed to
OK (There is an initial response) A
NG (Waveform output remains LO) B
NG (There is no initial response and the waveform output remains HI) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

3.CHECK HARNESS AND CONNECTOR (BODY ECU - MAP LIGHT ASSEMBLY)

C

4.INSPECT MAP LIGHT ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (BODY ECU - MAP LIGHT ASSEMBLY)
a.

Disconnect the G34 body ECU connector.


b.

Disconnect the Q2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G34-12 (ISIF) - Q2- 8 (IND1) Always Below 1 Ω
G34-12 (ISIF) - Body ground Always 10 kΩ or higher
Q2- 8 (IND1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>MAP LIGHT BULB>REPLACEMENT


b.
B419471E01
1.49,1.552 1.927,1.802 0.438,0.25 1.5,0.25 1.938,0.5 0.438,0.25 1.25,0.583 1.427,0.583 1.427,0.583 1.563,0.969 true 1.781,0.99 2.01,0.573 2.01,0.573 2.188,0.573 true 1.917,1.063 2.073,1.354 2.073,1.354 2.25,1.354 true 0.51,3.042 0.688,3.042 0.688,3.042 1.031,2.688 true 0.51,1.688 0.688,1.688 0.688,1.688 1.021,2.375 true 2.031,2.385 2.344,1.698 2.344,1.698 2.521,1.698 true 0.927,0.5 1.385,0.698 0.458,0.198 10 false +B2 2.271,0.479 2.729,0.677 0.458,0.198 10 false IND1 2.302,1.281 2.76,1.479 0.458,0.198 10 false GND 0.198,2.958 0.656,3.156 0.458,0.198 10 false +B2 0.146,1.615 0.604,1.813 0.458,0.198 10 false IND1 2.583,1.604 3.042,1.802 0.458,0.198 10 false GND 1.646,1.594 2.104,1.792 0.458,0.198 10 false B 1.667,0.292 2.125,0.49 0.458,0.198 10 false A

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (GND) -B-3 (GND) Always Below 1 Ω
A-2 (IND1) -B-8 (IND1) Always Below 1 Ω
A-4 (+B2) - B-16 (+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG

REPLACE MAP LIGHT ASSEMBLY