When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
11320
1.INSTALL TIMING GEAR CASE ASSEMBLY
15104
2.INSTALL OIL STRAINER SUB-ASSEMBLY
12101
3.INSTALL OIL PAN SUB-ASSEMBLY
22100
4.INSTALL FUEL SUPPLY PUMP ASSEMBLY
13613E
5.INSTALL INJECTION GEAR
13521
6.INSTALL CRANKSHAFT TIMING GEAR
13581
7.INSTALL NO. 1 IDLE GEAR SHAFT
13525
8.INSTALL NO. 1 IDLE GEAR
19315
9.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
10.INSTALL TIMING GEAR COVER
13408
11.INSTALL CRANKSHAFT PULLEY SUB-ASSEMBLY
13522P
12.INSTALL PUMP DRIVE SHAFT PULLEY
Install a new O-ring to the fuel supply pump assembly.
Temporarily install the fuel supply pump assembly with the nut.
| *a | Hold |
|
Turn |
Using SST, hold the crankshaft pulley and tighten the nut.
Install the No. 2 camshaft timing pulley flange and pump drive shaft pulley to the timing gear cover with the 4 bolts.
Using a dial indicator, check the thrust clearance of the pump drive shaft while moving the pump drive shaft pulley back and forth.
0.15 to 0.55 mm (0.00591 to 0.0217 in.)
If there is no clearance, remove and reinstall the fuel supply pump assembly and pump drive shaft pulley. Then repeat the step above.
13.INSTALL CRANKSHAFT POSITION SENSOR
14.INSTALL CAMSHAFT POSITION SENSOR
44320
15.INSTALL VANE PUMP ASSEMBLY
29300
16.INSTALL VACUUM PUMP ASSEMBLY
16100
17.INSTALL ENGINE WATER PUMP ASSEMBLY
11322B
18.INSTALL NO. 2 TIMING BELT COVER
13523P
19.INSTALL CAMSHAFT TIMING PULLEY
11201
20.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
23804C
21.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
15301
22.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
23704
23.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY
23701
24.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY
17118
25.INSTALL MANIFOLD STAY
88431
26.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET
16620
27.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
12511C
28.INSTALL GENERATOR BRACKET
27020
29.INSTALL GENERATOR ASSEMBLY
for 80A Type:
Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>GENERATOR(for 80A Type)>INSTALLATION
for 90A Type:
Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>GENERATOR(for 90A Type)>INSTALLATION
for 100A Type:
Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>GENERATOR(for 100A Type)>INSTALLATION
88440D
30.INSTALL NO. 2 IDLE PULLEY ASSEMBLY
for 80A Type:
Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>GENERATOR(for 80A Type)>INSTALLATION
for 90A Type:
Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>GENERATOR(for 90A Type)>INSTALLATION
for 100A Type:
Click herePower Source / Network>1KD-FTV BATTERY / CHARGING>GENERATOR(for 100A Type)>INSTALLATION
13505
31.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
13568
32.INSTALL TIMING BELT
11322A
33.INSTALL NO. 1 TIMING BELT COVER
34.INSTALL ENGINE ASSEMBLY
35.ADD ENGINE OIL
36.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
37.BLEED AIR FROM FUEL SYSTEM
38.ADD ENGINE COOLANT
39.BLEED AIR FROM POWER STEERING SYSTEM
40.INSPECT FOR POWER STEERING FLUID LEVEL
41.PERFORM REGISTRATION
Perform registration of the injector compensation codes.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION
Perform pilot quantity learning.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION
42.INSPECT FOR OIL LEAK
43.INSPECT FOR COOLANT LEAK
44.INSPECT FOR EXHAUST GAS LEAK
45.INSPECT FOR FUEL LEAK
46.INSPECT ENGINE OIL LEVEL