Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2015.11–2016.07
RM33K0E _55 Steering _043538 POWER ASSIST SYSTEMS _0227297 POWER STEERING SYSTEM G

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 2.BLEED AIR FROM POWER STEERING SYSTEM

NOTICE:

Do not allow foreign matter in the oil reservoir sub-assembly.


a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the steering wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine. Run the engine at idle for a few minutes.


f.

Turn the steering wheel.

i.

With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.


ii.

Repeat the step above several times.



g.

Stop the engine.


h.
F040897C12
0.323,0.24 1.135,0.427 0.813,0.188 10 false *a 2.135,0.24 3.094,0.427 0.958,0.188 10 false *b
*a Correct
*b Incorrect


Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.


i.

Check the fluid level.


Hide 3.CHECK FLUID LEVEL

NOTICE:

Do not allow foreign matter in the oil reservoir sub-assembly.


a.

Keep the vehicle level.


b.
C333669

With the engine stopped, check the power steering fluid level in the oil reservoir. If necessary, add power steering fluid.

Power steering fluid:

Automatic transmission Fluid DEXRON II or III or equivalent


HINT:

If the fluid is hot, check that the fluid level is within the HOT range on the oil reservoir. If the fluid is cold, check that the fluid level is within the COLD range.



c.

Start the engine and run it at idle.


d.

Turn the steering wheel to the left or right full lock position, and then turn the steering wheel to the opposite full lock position. Repeat this several times to raise the fluid temperature.

Standard fluid temperature:

40 to 80°C (104 to 176°F)



e.
F040897C12
0.323,0.24 1.135,0.427 0.813,0.188 10 false *a 2.135,0.24 3.094,0.427 0.958,0.188 10 false *b
*a Correct
*b Incorrect


Check for foaming or emulsification. If foaming or emulsification is identified, bleed air from the power steering system.


f.
R011786C07
0.708,1.792 0.948,1.979 0.24,0.188 10 false *a 2.469,1.792 2.719,1.979 0.25,0.188 10 false *b 1.427,0.448 1.688,0.625 0.26,0.177 10 false *c
*a Engine idling
*b Engine stopped
*c 5 mm or less


With the engine idling, measure the fluid level in the oil reservoir.


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the oil reservoir.

Maximum fluid level increase:

5 mm (0.197 in.)


If a problem is found, bleed air from the power steering system.


i.

Check the fluid level.


Hide 4.CHECK STEERING FLUID PRESSURE


b.

Connect SST as shown in the illustration below.

SST
09640-10011  (09641-01010, 09641-01030, 09641-01040)

C262273C03
2.99,2.031 2.01,2.594 2.01,2.594 1.729,2.594 true 6.052,0.604 6.188,0.333 6.188,0.333 6.313,0.333 false 2.917,1.823 2.583,1.427 true 0.469,0.896 0.875,1.094 0.406,0.198 10 false *2 1.531,2.521 1.792,2.719 0.26,0.198 10 false *1 5.458,1.802 5.729,1.979 0.271,0.177 10 false *a 6.698,1.802 7.01,1.979 0.313,0.177 10 false *b 6.375,0.25 6.75,0.469 0.375,0.219 10 false SST 0.177,0.167 0.5,0.354 0.323,0.188 10 false *A 2.323,2.625 2.625,2.813 0.302,0.188 10 false *2 2.438,1.323 2.698,1.521 0.26,0.198 10 false *3
*A for 1GR-FE - -
*1 Pressure Feed Tube *2 Attachment
*3 Gasket - -
*a In *b Out


C322695C01
6.271,1.104 6.688,0.688 false 2.969,1.833 3.323,2.146 true 2.333,2.417 2.677,2.198 true 0.188,0.24 0.5,0.396 0.313,0.156 10 false *A 6.729,0.573 7.125,0.781 0.396,0.208 10 false SST 2.167,2.344 2.354,2.573 0.188,0.229 10 true *1 0.979,0.24 1.292,0.396 0.313,0.156 10 false *2 5.573,1.177 5.885,1.333 0.313,0.156 10 false *a 6.552,1.188 6.865,1.344 0.313,0.156 10 false *b 3.844,2.813 4.156,2.969 0.313,0.156 10 false *2 3.375,2.104 3.594,2.313 0.219,0.208 10 true *3
*A for 1GD-FTV - -
*1 Pressure Feed Tube *2 Attachment
*3 Gasket - -
*a In *b Out


G100333C05
3.948,0.917 3.813,0.479 3.813,0.479 3.552,0.479 false 1.854,0.698 1.688,0.427 1.688,0.427 1.417,0.427 false 1.094,0.333 1.448,0.521 0.354,0.188 10 false SST 3.344,0.385 3.573,0.573 0.229,0.188 10 false *1 4.885,0.833 5.042,1.021 0.156,0.188 10 false *2 5.146,2.448 5.354,2.646 0.208,0.198 10 false *2 1.75,1.396 1.927,1.583 0.177,0.188 10 false *a 2.667,1.396 2.927,1.604 0.26,0.208 10 false *b 0.208,0.146 0.573,0.354 0.365,0.208 10 false *A
*A for 1KD-FTV - -
*1 Pressure Feed Tube *2 Attachment
*a In *b Out


C323292C01
3.958,2.677 3.521,2.448 true 3,2.406 2.688,2.104 true 6.219,1.167 6.563,0.875 false 0.229,0.177 0.542,0.333 0.313,0.156 10 false *A 2.49,1.99 2.75,2.302 0.26,0.313 10 true *1 1.688,2.865 2,3.021 0.313,0.156 10 false *2 4,2.646 4.313,2.802 0.313,0.156 10 false *3 5.521,1.354 5.833,1.51 0.313,0.156 10 false *a 6.542,1.354 6.854,1.51 0.313,0.156 10 false *b 3.792,0.448 4.104,0.604 0.313,0.156 10 false *2 6.635,0.74 6.938,0.99 0.302,0.25 10 false SST
*A for 2TR-FE - -
*1 Pressure Feed Tube *2 Attachment
*3 Gasket - -
*a In *b Out


NOTICE:

Check that the valve of SST is in the open position.



c.

Bleed air from the power steering system.

NOTICE:

Check the level of power steering fluid and refill as necessary.



d.

Start the engine and run it at idle.


e.

Turn the steering wheel to the left or right full lock position. Then turn the steering wheel to the opposite full lock position. Repeat this several times to raise the fluid temperature.

Standard fluid temperature:

40 to 80°C (104 to 176°F)



f.
C114329C07
0.448,0.885 0.656,1.063 0.208,0.177 10 false *1 2.708,1.542 2.958,1.719 0.25,0.177 10 false *3 2.708,0.271 2.927,0.438 0.219,0.167 10 false *2 1.344,1.042 1.656,1.25 0.313,0.208 10 false *a 1.531,1.896 1.896,2.104 0.365,0.208 10 false SST
*1 Power Steering Link
*2 Oil Reservoir
*3 Vane Pump Assembly
*a Closed


With the engine idling, close the valve of SST and observe the reading on SST.

Maximum fluid pressure:
for 1GR-FE:

8800 to 9300 kPa (89.8 to 94.8 kgf/cm2, 1276 to 1348 psi)

for 1GD-FTV:

9300 to 10000 kPa (94.9 to 101 kgf/cm2, 1349 to 1450 psi)

for 1KD-FTV:

8800 to 9300 kPa (89.8 to 94.8 kgf/cm2, 1276 to 1348 psi)

for 2TR-FE:

8800 to 9300 kPa (89.8 to 94.8 kgf/cm2, 1276 to 1348 psi)


NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not let the fluid temperature become too high.



If the pressure is above the maximum, check for fluid leaks and replace parts as necessary.


g.
C114330C07
0.438,0.896 0.656,1.073 0.219,0.177 10 false *1 1.531,1.885 1.896,2.094 0.365,0.208 10 false SST 1.354,1.052 1.771,1.26 0.417,0.208 10 false *a 2.708,0.26 2.906,0.427 0.198,0.167 10 false *2 2.698,1.542 2.927,1.708 0.229,0.167 10 false *3
*1 Power Steering Link
*2 Oil Reservoir
*3 Vane Pump Assembly
*a Open


With the engine idling, fully open the valve.


h.

Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

Standard fluid pressure difference:

490 kPa (4.99 kgf/cm2, 71 psi) or less


NOTICE:

Do not turn the steering wheel.


If the pressure difference is not within the specified range, check for fluid leaks and replace parts as necessary.


i.
C114331C07
2.708,0.281 2.99,0.458 0.281,0.177 10 false *2 2.708,1.542 2.938,1.729 0.229,0.188 10 false *3 1.521,1.896 1.948,2.094 0.427,0.198 10 false SST 1.344,1.063 1.75,1.26 0.406,0.198 10 false *a 0.438,0.906 0.792,1.156 0.354,0.25 10 false *1 1.563,0.479 1.906,0.677 0.344,0.198 10 false *b
*1 Power Steering Link
*2 Oil Reservoir
*3 Vane Pump Assembly
*a Open
*b Steering wheel to the full lock position


With the engine idling and the valve fully opened, turn the steering wheel to the full lock position.

Maximum fluid pressure:
for 1GR-FE:

8800 to 9300 kPa (89.8 to 94.8 kgf/cm2, 1276 to 1348 psi)

for 1GD-FTV:

9300 to 10000 kPa (94.9 to 101 kgf/cm2, 1349 to 1450 psi)

for 1KD-FTV:

8800 to 9300 kPa (89.8 to 94.8 kgf/cm2, 1276 to 1348 psi)

for 2TR-FE:

8800 to 9300 kPa (89.8 to 94.8 kgf/cm2, 1276 to 1348 psi)


NOTICE:
·

Do not keep the steering wheel in the lock position for more than 10 seconds.

·

Do not let the fluid temperature become too high.



If the pressure is above the maximum, check for fluid leaks and replace parts as necessary.


j.

Disconnect SST.



l.

Bleed air from the power steering system.

NOTICE:

Check the level of power steering fluid and refill as necessary.



Hide 5.CHECK STEERING RESISTANCE

a.

Center the steering wheel.


b.

Remove the steering pad.


c.

Start the engine and run it at idle.


d.

Measure the steering resistance in both directions.

Standard steering resistance (Reference):

6.0 N*m (61 kgf*cm, 53 in.*lbf)


HINT:

The tire type, tire pressure and type of surface beneath the vehicle should be taken into consideration before making your diagnosis.



e.

Install the steering pad.