Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › CAMSHAFT
RM33K0E _51 Engine / Hybrid System _043570 2TR-FE ENGINE MECHANICAL _0225063 CAMSHAFT A

2TR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of ignition coil assembly


Inspection after repair Poor idle, engine start, etc. (Click here)

CAUTION:
A343693

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 16361A 3.REMOVE FAN AND GENERATOR V BELT

Hide 17861 4.REMOVE INTAKE AIR CONNECTOR

Hide 11201 6.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11204 7.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 9.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A337700C01
2.698,1.031 2.031,1.188 2.031,1.188 2.698,0.771 true 1.125,0.635 1.396,1.344 1.396,1.344 1.01,0.854 true 0.865,2.396 0.635,2.104 0.635,2.104 0.448,2.104 true 2.458,2.427 2.729,2.104 2.729,2.104 2.854,2.104 true 2.615,3.792 2.365,3.792 2.365,3.792 1.823,4.219 true 1.854,1.083 2.042,1.271 0.188,0.188 10 true *a 2.646,3.698 2.844,3.885 0.198,0.188 10 true *b 1.063,0.104 1.25,0.292 0.188,0.188 10 true *c 1.344,1.354 1.531,1.542 0.188,0.188 10 true *a 0.24,2 0.427,2.188 0.188,0.188 10 true *a 2.875,2 3.063,2.188 0.188,0.188 10 true *a
*a Timing Mark
*b Groove
*c Approximately 13°


Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover sub-assembly.


b.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the No. 1 camshaft bearing cap as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



Hide 13540 10.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A337701C01
0.354,0.51 0.542,0.51 0.542,0.51 0.875,0.813 true 0.229,1.115 0.365,1.115 0.365,1.115 0.896,0.885 true 2.479,0.823 2.75,0.521 2.75,0.521 2.906,0.521 true 2.49,0.927 3.052,1.104 3.052,1.104 3.177,1.104 true 0.156,0.406 0.344,0.604 0.188,0.198 10 false *a 0.031,1.01 0.219,1.198 0.188,0.188 10 false *b 2.948,0.417 3.135,0.615 0.188,0.198 10 false *a 3.208,1.01 3.396,1.198 0.188,0.188 10 false *b
*a Paint Mark
*b Timing Mark


Place paint marks on the chain sub-assembly, camshaft timing gear assembly and camshaft timing exhaust gear assembly.


b.
A337702

Remove the 2 bolts and timing chain cover plate from the timing chain cover sub-assembly.


c.

Remove the gasket from the timing chain cover plate.


d.
A101303C25
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.26,1.615 2.49,1.792 0.229,0.177 10 false *b 0.5,1.875 0.698,2.063 0.198,0.188 10 false *c 2.729,0.25 2.917,0.458 0.188,0.208 10 false *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner assembly.


e.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.


f.
A340033

Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.


Hide 13512 11.REMOVE NO. 2 CAMSHAFT

a.
A337706

Uniformly loosen the 12 bolts and then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the No. 2 camshaft level.



b.

Move the camshaft in the direction shown in the illustration to loosen the chain sub-assembly, and then remove the No. 2 camshaft.

A337707C01
0.583,0.333 0.729,0.333 0.729,0.333 1.177,0.573 true 2.021,0.688 2.469,0.333 2.469,0.333 2.656,0.333 true 0.333,0.875 0.479,0.875 0.479,0.875 0.646,1.438 true 0.406,0.24 0.594,0.438 0.188,0.198 10 false *2 0.135,0.771 0.323,0.969 0.188,0.198 10 false *3 2.698,0.229 2.885,0.427 0.188,0.198 10 false *1
*1 Camshaft *2 No. 2 Camshaft
*3 Chain Sub-assembly - -


NOTICE:

Do not pry the No. 2 camshaft with a tool as an excessive amount of force may be applied to it.



Hide 13511 12.REMOVE CAMSHAFT

a.
A337714

Uniformly loosen the 8 bolts and then remove the 4 No. 2 camshaft bearing caps.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



b.
A337708

Remove the camshaft while holding the chain sub-assembly.

NOTICE:

Do not pry the camshaft with a tool as an excessive amount of force may be applied to it.



c.
A337709

Secure the chain sub-assembly with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover sub-assembly.



Hide 13050 13.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the lock of the camshaft timing gear assembly.

i.
A346182C01
0.646,0.688 0.833,0.688 0.833,0.688 0.979,1.313 true 2.219,1.052 2.344,1.052 2.344,1.052 2.698,0.896 true 2.031,0.938 2.229,1.135 0.198,0.198 10 false *a 0.323,0.594 0.656,0.792 0.333,0.198 10 false SST
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure SST and camshaft in a vise as shown in the illustration and check that the camshaft timing gear assembly does not rotate.

SST
09212-31010  

NOTICE:
·

Do not damage the camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.





b.

Release the lock pin.

i.

Clean the camshaft journal with non-residue solvent.


ii.
A336435C01
1.521,1.448 0.594,0.646 0.594,0.646 1.896,1.354 true 1.521,1.594 2.333,2.188 2.333,2.188 1.917,1.667 true 2.052,3.26 2.417,3.5 2.417,3.5 2.604,3.5 true 2.063,3.76 2.615,3.76 true 0.833,3.781 0.979,3.781 0.979,3.781 1.385,3.635 false 0.854,3.406 1.375,3.406 true 0.385,0.521 0.583,0.719 0.198,0.198 10 false *a 2.375,2.156 2.573,2.333 0.198,0.177 10 false *b 2.646,3.396 2.833,3.573 0.188,0.177 10 false *c 2.656,3.667 2.854,3.854 0.198,0.188 10 false *d 0.656,3.302 0.865,3.49 0.208,0.188 10 false *d 0.656,3.677 0.854,3.875 0.198,0.198 10 false *c
*a Retard Side Path
*b Advance Side Path
*c Open
*d Close
V100144

Rubber Piece
V100145

Vinyl Tape


Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

1 retard side path and 1 advance side path are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.



iii.

Break through the tape over the advance side path, and then break through the tape over the retard side path on the opposite side from the hole over the advance side path as shown in the illustration.


iv.
A336436C01
0.677,0.573 0.927,0.573 0.927,0.573 1.552,1.24 true 1.865,1.396 2.438,0.573 2.438,0.573 2.615,0.573 true 0.469,0.458 0.667,0.656 0.198,0.198 10 false *a 2.646,0.469 2.854,0.667 0.208,0.198 10 false *b
*a Retard Side Path
*b Advance Side Path


Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths accessible through the holes in the tape.

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



v.
A336437C01
0.708,0.656 0.917,0.656 0.917,0.656 1.542,1.229 true 1.844,1.396 2.458,0.667 2.458,0.667 2.667,0.667 true 0.51,0.542 0.708,0.74 0.198,0.198 10 false *a 2.688,0.563 2.885,0.76 0.198,0.198 10 false *b 0.906,1.656 1.104,1.854 0.198,0.198 10 false *c 2.396,1.74 2.594,1.938 0.198,0.198 10 false *d
*a Retard Side Path
*b Advance Side Path
*c Decompress
*d Hold Pressure


Check that the camshaft timing gear assembly revolves in the advance direction when reducing the air pressure applied to the retard side path.

OK:

Gear rotates in the advance direction.


HINT:

This operation releases the lock pin which holds the timing gear in the most retarded position.



vi.

When the camshaft timing gear assembly reaches the most advanced position, release the air pressure from the retard side path and advance side path in that order.

NOTICE:
·

Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

·

When releasing the air pressure from the advance side path, release it slowly.





c.

Check for smooth rotation.

i.

Rotate the camshaft timing gear assembly within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.

CAUTION:

Do not use air pressure to perform the smooth operation check.




d.

Check the lock in the most retarded position.

i.

Confirm that the camshaft timing gear assembly becomes locked at the most retarded position.



Hide 13050 14.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A344523C01
2.25,1.052 2.354,1.052 2.354,1.052 2.667,0.969 true 0.729,0.563 0.896,0.563 0.896,0.563 0.979,1.313 true 0.406,0.479 0.729,0.656 0.323,0.177 10 false SST 2.063,0.948 2.26,1.146 0.198,0.198 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure SST and camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A336434C01
0.26,1.813 0.26,1.5 false 1.594,0.938 1.594,0.385 1.594,0.385 1.729,0.385 false 0.521,0.49 0.771,0.49 0.771,0.49 1.198,1.323 true 0.896,0.958 0.781,0.5 false 0.875,1.396 0.771,0.5 false 0.313,0.385 0.5,0.573 0.188,0.188 10 false *b 1.76,0.281 1.948,0.469 0.188,0.188 10 false *a 0.198,1.844 0.385,2.031 0.188,0.188 10 false *1
*1 Flange Bolt
*a Straight Pin
*b Do Not Remove


Remove the flange bolt and camshaft timing gear assembly.

NOTICE:
·

Be sure not to remove the other 3 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.




Hide 13070A 15.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Check the lock of the camshaft timing exhaust gear assembly.

i.
A346182C01
0.646,0.688 0.833,0.688 0.833,0.688 0.979,1.313 true 2.219,1.052 2.344,1.052 2.344,1.052 2.698,0.896 true 2.031,0.938 2.229,1.135 0.198,0.198 10 false *a 0.323,0.594 0.656,0.792 0.333,0.198 10 false SST
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure SST and No. 2 camshaft in a vise as shown in the illustration and check that the camshaft timing exhaust gear assembly does not rotate.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.





b.

Release the lock pin.

i.

Clean the No. 2 camshaft journal with non-residue solvent.


ii.
A336443C01
0.813,3.448 0.979,3.448 0.979,3.448 1.438,3.302 true 0.813,3.854 0.979,3.854 0.979,3.854 1.438,3.708 true 2.01,3.406 2.531,3.406 true 1.99,3.604 2.344,3.76 2.344,3.76 2.531,3.76 true 1.906,1.5 0.896,1.594 0.896,1.594 1.51,1.396 true 1.531,1.719 2.479,1.979 2.479,1.979 1.896,1.625 true 2.521,1.906 2.729,2.104 0.208,0.198 10 false *a 0.698,1.51 0.896,1.708 0.198,0.198 10 false *b 0.625,3.333 0.802,3.531 0.177,0.198 10 false *c 0.625,3.76 0.833,3.948 0.208,0.188 10 false *d 2.542,3.292 2.729,3.479 0.188,0.188 10 false *d 2.563,3.656 2.76,3.854 0.198,0.198 10 false *c
*a Retard Side Path
*b Advance Side Path
*c Open
*d Close
V100144

Rubber Piece
V100145

Vinyl Tape


Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the No. 2 camshaft. Plug 2 paths with pieces of rubber.



iii.

Break through the tape over the advance side path, and then break through the tape over the retard side path on the opposite side from the hole over the advance side path as shown in the illustration.


iv.
A336444C01
0.698,0.604 0.896,0.604 0.896,0.604 1.542,1.344 true 1.896,1.167 2.427,0.625 2.427,0.625 2.646,0.625 true 0.5,0.49 0.688,0.698 0.188,0.208 10 false *a 2.667,0.521 2.865,0.708 0.198,0.188 10 false *b
*a Retard Side Path
*b Advance Side Path


Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths (the advance side path and retard side path).

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.


HINT:

The lock pin is released in this condition.



v.
A336445C01
0.688,0.521 0.865,0.521 0.865,0.521 1.552,1.344 true 1.885,1.188 2.458,0.521 2.458,0.521 2.656,0.521 true 0.49,0.417 0.688,0.625 0.198,0.208 10 false *a 2.677,0.427 2.875,0.615 0.198,0.188 10 false *b 2.438,1.542 2.615,1.74 0.177,0.198 10 false *c 0.969,1.76 1.167,1.948 0.198,0.188 10 false *d
*a Retard Side Path
*b Advance Side Path
*c Decompress
*d Hold Pressure


Check that the camshaft timing exhaust gear assembly turns in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



vi.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




c.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (21.5 to 23.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the gear automatically returns to the most advanced position due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




d.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



Hide 13070A 16.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A344523C01
2.25,1.052 2.354,1.052 2.354,1.052 2.667,0.969 true 0.729,0.563 0.896,0.563 0.896,0.563 0.979,1.313 true 0.406,0.479 0.729,0.656 0.323,0.177 10 false SST 2.063,0.948 2.26,1.146 0.198,0.198 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure SST and No. 2 camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A336439C01
0.25,1.917 0.25,1.615 false 1.573,1.083 1.573,0.552 1.573,0.552 1.729,0.552 false 0.771,1.146 0.635,0.802 0.635,0.802 1.01,1.188 true 0.833,1.573 0.938,1.865 0.938,1.865 1.063,1.563 true 0.188,1.948 0.396,2.135 0.208,0.188 10 false *1 1.76,0.458 1.958,0.667 0.198,0.208 10 false *a 0.458,0.667 0.646,0.865 0.188,0.198 10 false *b 0.875,1.896 1.073,2.083 0.198,0.188 10 false *b
*1 Flange Bolt
*a Straight Pin
*b Do Not Remove


Remove the flange bolt and camshaft timing exhaust gear assembly.

NOTICE:

Be sure not to remove the other 4 bolts.