Home › Engine / Hybrid System › 2TR-FE LUBRICATION › OIL PUMP
RM33K0E _51 Engine / Hybrid System _043524 2TR-FE LUBRICATION _0225074 OIL PUMP A

2TR-FE LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the throttle body with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of throttle body with motor assembly Inspection After Repair Poor idle, engine start, etc. (Click here)
Cleaning the deposits from the throttle body with motor assembly

PROCEDURE

Hide 22030 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 23814B 7.REMOVE FUEL DELIVERY PIPE

Hide 23250 8.REMOVE FUEL INJECTOR ASSEMBLY

Hide 88431 11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 16620D 12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16321 13.REMOVE WATER INLET

Hide 16331A 14.REMOVE THERMOSTAT

Hide 16603 15.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16268 16.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 12108 17.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 11301M 18.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11301M 19.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11101J 20.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11201 21.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A336469

Remove the 21 bolts, 2 nuts, 2 plate washers, 2 seal washers and cylinder head cover sub-assembly.


b.

Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.


c.

Remove the No. 1 camshaft bearing cap oil hole gasket from the cylinder head cover connector sub-assembly.


Hide 13471 22.REMOVE CRANKSHAFT PULLEY

a.
A344593C01
1.375,0.708 0.927,0.354 true 0.583,0.354 0.917,0.354 0.917,0.354 1.479,0.5 true 2.448,1.917 2.667,2.094 0.219,0.177 10 true *a 0.281,0.281 0.604,0.5 0.323,0.219 10 false SST
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A344594N01
0.646,1.094 1.083,1.094 false 0.344,1.021 0.646,1.208 0.302,0.188 10 false SST

Using SST and the crankshaft pulley set bolt, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05021)

HINT:

Apply lubricant to the threads and end of SST.



Hide 12144 23.REMOVE OIL PAN COVER SILENCER

a.

Remove the 4 No. 1 oil pan plugs and oil pan cover silencer.


Hide 12102A 24.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove the oil pan drain plug and gasket.


b.
A346220

Remove the 16 bolts, 4 adjusting screws and 2 nuts.


c.
A344595

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.



Hide 15104 25.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A334454

Remove the 2 bolts, nut, oil strainer sub-assembly and gasket.


Hide 12101 26.REMOVE OIL PAN SUB-ASSEMBLY

a.
A346221

Remove the 16 bolts and 2 nuts.


b.
A344596C01
1.563,1.948 1.708,1.948 1.708,1.948 1.844,1.625 true 1.396,1.854 1.552,2.063 0.156,0.208 10 true *a
*a Protective Tape


Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11301K 27.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11302 28.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A346223

Remove the 16 bolts and nut shown in the illustration.


b.
A346224C01
0.427,0.542 0.719,0.542 true 0.427,2.906 0.573,3.094 0.573,3.094 0.708,3.094 true 2.719,3.052 2.833,3.052 2.833,3.052 2.958,2.615 true 2.698,0.885 2.781,0.99 2.781,0.99 2.917,0.99 true 0.24,0.458 0.469,0.646 0.229,0.188 10 false *a 0.75,3 0.979,3.188 0.229,0.188 10 false *a 2.927,0.906 3.125,1.094 0.198,0.188 10 true *a 2.552,2.958 2.74,3.146 0.188,0.188 10 false *a
*a Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A346225

Remove the 3 O-rings.


Hide 16100 29.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A336766

Remove the 8 bolts, engine water pump assembly and gasket.


Hide 11303A 30.REMOVE TIMING CHAIN CASE OIL SEAL

a.
A336767C01
0.594,0.396 0.771,0.396 0.771,0.396 1.438,0.781 true 1.458,1.729 0.552,1.75 0.552,1.75 0.781,1.094 true 0.417,0.323 0.615,0.531 0.198,0.208 10 false *a 0.365,1.698 0.594,1.885 0.229,0.188 10 false *b
*a Protective Tape
*b Wooden Block


Place the timing chain cover sub-assembly on wooden blocks.


b.

Using a screwdriver, pry out the timing chain case oil seal.

HINT:

Tape the screwdriver tip before use.