Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM33K0E _51 Engine / Hybrid System _043570 2TR-FE ENGINE MECHANICAL _0225067 ENGINE ASSEMBLY A

2TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P0630 is output (Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly Inspection after repair Poor idle, engine start, etc. (Click here)
·

Replacement of throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of piston or piston ring

·

Replacement of mass air flow meter sub-assembly

·

Replacement of fuel injector assembly

·

Replacement of fuel pump

·

Replacement of air fuel ratio sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Replacement of knock sensor


Inspection after repair Poor idle, engine start, etc. (Click here)
for AC60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for AC60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

CAUTION:
·
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·
A343701

Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A343693

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD (for 4WD)

Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 8.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 9.DRAIN DIFFERENTIAL OIL (for 4WD)

Hide 53301 10.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose from the hood sub-assembly.


b.

Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.


Hide 17705 11.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

a.
A346135

Disconnect the intake mass air flow meter connector and detach the 2 wire harness clamps.


b.
A346136

Detach the 4 clamps.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.


Hide 17801 12.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 17701 13.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A344949

Detach the 3 wire harness clamps.


b.
A349779

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 17861 14.REMOVE INTAKE AIR CONNECTOR

Hide 51410 15.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 16.REMOVE NO. 2 ENGINE UNDER COVER

Hide 51407A 17.REMOVE NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Cover)

Hide 53737B 18.REMOVE FRONT UPPER FENDER APRON SEAL LH

a.

Remove the 6 clips and front upper fender apron seal LH.


Hide 53736 19.REMOVE FRONT UPPER FENDER APRON SEAL RH

a.

w/ Secondary Air Injection System:

i.

Remove the 5 clips and front upper fender apron seal RH.



b.

w/o Secondary Air Injection System:

i.

Remove the 6 clips and front upper fender apron seal RH.



Hide 53882F 20.REMOVE FRONT FENDER SEAL LH

a.

Remove the 6 clips and front fender seal LH.


Hide 53882F 21.REMOVE FRONT FENDER SEAL RH

a.

Remove the 6 clips and front fender seal RH.


Hide 53294C 22.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 53293C 23.REMOVE RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 16593 24.REMOVE NO. 1 RADIATOR AIR GUIDE

Hide 16571 25.REMOVE RADIATOR HOSE INLET

Hide 16572 26.REMOVE RADIATOR HOSE OUTLET

Hide 17621A 27.DISCONNECT AIR PUMP INLET (w/ Secondary Air Injection System)

Hide 16470 28.REMOVE RADIATOR RESERVOIR

Hide 16711 29.REMOVE FAN SHROUD

Hide 32941 30.DISCONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32942 31.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 16400 32.REMOVE RADIATOR ASSEMBLY

Hide 33.DISCONNECT HEATER HOSE

a.
A356083C01
1.094,3.479 1.375,3.479 true 0.99,1.156 1.26,1.156 true 1.677,1.052 1.979,0.76 1.979,0.76 2.177,0.76 true 1.729,3.406 2.031,3.115 2.031,3.115 2.229,3.115 true 0.052,0.042 0.292,0.24 0.24,0.198 10 true *A 0.052,2.438 0.271,2.646 0.219,0.208 10 true *B 0.781,1.063 0.99,1.26 0.208,0.198 10 true *1 2.198,0.656 2.406,0.844 0.208,0.188 10 true *2 0.885,3.385 1.083,3.583 0.198,0.198 10 true *1 2.25,3.021 2.458,3.219 0.208,0.198 10 true *2
*A for LHD
*B for RHD
*1 Heater Water Outlet Hose
*2 Heater Water Inlet Hose


Slide the clamp and disconnect the heater water outlet hose from the heater radiator unit sub-assembly.


b.

Slide the clamp and disconnect the heater water inlet hose from the heater radiator unit sub-assembly.


Hide 44320 34.DISCONNECT VANE PUMP ASSEMBLY

a.

Disconnect the power steering oil pressure switch connector.


b.
A348584

Remove the 2 bolts and disconnect the vane pump assembly.

NOTICE:

Do not hit other parts with the pulley when disconnecting the vane pump assembly.


HINT:

Be sure to suspend the vane pump assembly securely.



Hide 15301 35.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 36.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the bolt, engine oil level dipstick guide and O-ring.

NOTICE:

Cover the engine oil level dipstick guide hole to prevent foreign matter from entering it.



Hide 88320 37.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 28100 38.REMOVE STARTER ASSEMBLY

Hide 39.DISCONNECT PURGE LINE HOSE

A348567

a.

Slide the clamp and disconnect the purge line hose from the purge VSV.


Hide 44774 40.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A348566

Slide the clamp and disconnect the union to connector tube hose from the intake manifold.


Hide 17344 41.DISCONNECT NO. 4 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

Hide 23273C 42.DISCONNECT NO. 2 FUEL HOSE

Hide 23271H 43.DISCONNECT NO. 1 FUEL HOSE

Hide 55550 44.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 46.DISCONNECT ENGINE WIRE

a.
A356103C01
0.021,0.031 0.25,0.25 0.229,0.219 10 true *A 0.031,2.458 0.271,2.698 0.24,0.24 10 true *B
*A for LHD
*B for RHD


Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.


b.
A356104C01
0.021,0.031 0.25,0.25 0.229,0.219 10 true *A 0.031,2.427 0.25,2.656 0.219,0.229 10 true *B
*A for LHD
*B for RHD


w/ Secondary Air Injection System:

i.

Disconnect the air injection control driver connector.


ii.

Detach the clamp.


iii.

Remove the bolt and disconnect the engine wire from the air injection control bracket.



c.
A356105C01
0.021,0.031 0.25,0.26 0.229,0.229 10 true *A 0.042,2.438 0.271,2.656 0.229,0.219 10 true *B
*A for LHD
*B for RHD


w/o Secondary Air Injection System:

i.

Remove the bolt and disconnect the engine wire from the air injection control bracket.



d.
A356106C01
0.042,0.042 0.25,0.26 0.208,0.219 10 true *A 0.031,2.427 0.26,2.635 0.229,0.208 10 true *B
*A for LHD
*B for RHD


Detach the grommet and pull out the engine wire from the cabin.


e.
A356107C01
0.021,0.042 0.25,0.25 0.229,0.208 10 true *A 0.031,2.417 0.25,2.625 0.219,0.208 10 true *B
*A for LHD
*B for RHD


Disconnect the connector from the engine room main wire.


f.
A348572

Remove the nut and disconnect the engine room main wire from the positive (+) battery terminal.


g.
A348573

Loosen the nut and remove the positive (+) battery terminal.


h.
A348575

Loosen the 2 nuts and remove the battery hold down clamp.


i.

Remove the battery.


j.

Remove the battery tray.


k.
A348576

Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.


l.
A348577

Detach the clamp and remove the bolt and No. 2 engine wire.


m.
A348579

Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.


n.
A348580

Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.


o.
A348581

Remove the nut and disconnect the engine wire from the engine room relay block.


p.

Disconnect the 2 connectors from the engine room relay block.


q.

Detach the clamp.


r.
A348582

Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.


s.
A348583

Disconnect the air fuel ratio sensor connector.


t.

Remove the bolt and disconnect the sensor bracket from the right side of the frame.


Hide 17410 47.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 51.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

Hide 37100 52.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

Hide 43514C 53.REMOVE FRONT AXLE HUB GREASE CAP LH (for 4WD)

Hide 43502H 54.REMOVE FRONT AXLE SHAFT NUT LH (for 4WD)

Hide 89543 55.DISCONNECT FRONT SPEED SENSOR LH (for 4WD)

Hide 56.DISCONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)

Hide 48069 57.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH (for 4WD)

Hide 43420 58.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)

Hide 43410 59.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 43410D 60.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)

Hide 61.SECURE STEERING WHEEL ASSEMBLY (for 4WD)

Hide 45219 62.DISCONNECT STEERING SLIDING YOKE (for 4WD)

Hide 44250 63.REMOVE POWER STEERING LINK ASSEMBLY (for 4WD)

Hide 41110F 64.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

Hide 33030 65.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 31210 67.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 68.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 69.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 32101 70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 11355 71.REMOVE REAR END PLATE

a.
A348585

Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.


b.

Remove the bolt and rear end plate from the cylinder block sub-assembly.


Hide 72.INSTALL ENGINE HANGER

a.
A348586C01
0.042,0.021 0.229,0.229 0.188,0.208 10 false *a 1.854,0.021 2.063,0.219 0.208,0.198 10 false *b
*a Rear Side
*b Front Side


Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-0C010
12281-0C030
Bolt 90119-T0388
91672-81025



Hide 73.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A348587

Remove the 4 bolts and 4 nuts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




Hide 74.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 2 bolts and 2 engine hangers.


Hide 82121 75.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12391 76.REMOVE FRONT ENGINE MOUNTING HEAT INSULATOR RH

a.
A348589

Remove the bolt and front engine mounting heat insulator RH from the front engine mounting insulator.


Hide 12361 77.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A348590C01
0.052,0.031 0.271,0.25 0.219,0.219 10 false *a 0.052,2.469 0.271,2.688 0.219,0.219 10 true *b
*a LH Side
*b RH Side


Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.