CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY ECU
| *1 | Instrument Panel Junction Block Assembly (for LHD) | - | - |
| *1 | Instrument Panel Junction Block Assembly (for RHD) | - | - |
| *1 | Body ECU | - | - |
Remove the body ECU from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-7 (IG) - Body ground | - | IG power supply | Ignition switch ON | 11 to 14 V |
| A-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
Install the body ECU to the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: w/o Smart Entry and Start System *2: w/ Smart Entry and Start System *3: w/ Power Door Lock |
||||
| 2Q-9 (ILE) - Body ground | B - Body ground | Illumination signal | Map light and No. 1 room light switch in DOOR position and map light assembly, No. 1 room light assembly and transponder key coil*1 come on | Below 1 V |
| Map light and No. 1 room light switch in DOOR position and map light assembly, No. 1 room light assembly and transponder key coil*1 go off | 11 to 14 V | |||
| 2L-4 (DCTY) - Body ground | R - Body ground | Front door courtesy light switch assembly RH signal | Front door RH open | Below 1 V |
| Front door RH closed | Pulse generation | |||
| G33-14 (PCTY) - Body ground | LG - Body ground | Front door courtesy light switch assembly LH signal | Front door LH open | Below 1 V |
| Front door LH closed | Pulse generation | |||
| G33-15 (LSWD) - Body ground*3 | R - Body ground | Front door RH unlock detection switch signal | Front door RH locked | Pulse generation |
| Front door RH unlocked | Below 1 V | |||
| G33-8 (KSW) - Body ground*1 | G - Body ground | Unlock warning switch assembly signal | No key in ignition key cylinder | Pulse generation |
| Key in ignition key cylinder | Below 1 V | |||
| G33-9 (PRG) - Body ground*2 | V - Body ground | Signal output to certification ECU (smart key ECU assembly) | Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| 2Q-2 (ACTY) - Body ground | Y - Body ground | Door courtesy switch signal | All doors closed except driver door | Pulse generation |
| Any door open except driver door | Below 1 V | |||
| 2P-13 (DOMR) - Body ground | L - Body ground | Battery saving control (interior light auto cut function) signal | Battery saving control (interior light auto cut function) operating | 11 to 14 V |
| Battery saving control (interior light auto cut function) not operating | Below 1.7 V | |||
| G33-16 (RDA) - Body ground*2 | W - Body ground | Signal input from certification ECU (smart key ECU assembly) | Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| G33-2 (LSWP) - Body ground | Y - Body ground | Door unlock detection switch input (except front door RH) | Except front door RH unlocked | Below 1 V |
| Except front door RH locked | Pulse generation | |||
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G16-1 (+B) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| G16-10 (E) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G69 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G16-19 (SWIL) - G16-24 (AGND) | G - SB | Engine switch illumination drive output | Engine switch illumination on | 9 to 14 V |
| Engine switch illumination off | Below 2 V | |||
| G16-9 (LSWP) - G16-10 (E) | L - BR | Door unlock detection switch input (except front door RH) | Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch not pressed | Below 1 V |
| Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch pressed | 8.5 V or higher | |||
| G17-13 (RDA3) - G16-10 (E) | W - BR | Signal output to body ECU | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| G17-36 (PRG3) - G16-10 (E) | V - BR | Signal input from body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| G16-21 (ACCD) - G16-10 (E) | B - BR | ACC signal | Engine switch off → Engine switch on (ACC) | 1 V or less → 8.5 V or higher |
| G16-20 (IG1D) - G16-10 (E) | L - BR | IG1 signal | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU